background image

Page 2

Page 3

BOILERMA

TE 

2000

1.0 DESIGN

1.1 INTRODUCTION

T h e s e   i n s t r u c t i o n s   s h o u l d   b e   r e a d   i n  
conjunction with the Installation and Servicing 
Instructions  issued  by  the  manufacturers  of 
the heat source e.g. the boiler used.

Any  water  distribution  and  central  heating 
installation  must  comply  with  the  relevant 
recommendations  of  the  current  version  of 
the  Regulations  and  British  Standards  listed 
below:-

Gas Safety Regulations
Building Regulations
I.E.E. Requirements for Electrical Installations
Water Regulations

British Standards

BS6798,  BS5449,  BS5546,  BS5440:1,  BS5440:2, 
CP331:3, BS6700, BS5258, BS7593 and BS7671.

A  competent  person  as  stated  in  the  Gas 
Safety Regulations must install the BoilerMate 
heating  system.   The  manufacturer’s  notes 
must  not  be  taken  as  overriding  statutory 
obligations.

The  BoilerMate  2000  is  only  suitable  for  use 
with an open vented central heating system. 

The BoilerMate 2000 is not covered by section 
G3 of the current Building Regulations and is 
therefore not notifiable to Building Control.

The information in this manual is provided to 
assist generally in the selection of equipment.  
The  responsibility  for  the  selection  and 
specification of the equipment must however 
remain that of the customer and any Designers 
or Consultants concerned with the design and 
installation.

Please Note:  

We do not therefore accept any 

responsibility for matters of design, selection 
or specification or for the effectiveness of an 
installation  containing  one  of  our  products 
unless  we  have  been  specifically  requested 
to do so.

All goods are sold subject to our Conditions 
of  Sale,  which  are  set  out  at  the  rear  of  this 
manual.

In  the  interest  of  continuously  improving 
the BoilerMate range, Gledhill Water Storage 
Ltd  reserve  the  right  to  modify  the  product 
without  notice,  and  in  these  circumstances 
this document, which is accurate at the time 
of  printing,  should  be  disregarded.    It  will 
however be updated as soon as possible after 
the change has occurred.  

Summary of Contents for Gledhill BoilerMate 2000 125













































Reviews: