background image

Technical data

21

VG12_D00032_03_M_XXEN/01.2019

6.1   Standards and certifications

The following application standards must be considered:

 

DIN VDE 0100-410 (VDE 0100-410)
Low-voltage electrical installations – 
Part 4-41: Protection for safety, Protection against electric shock

 

DIN VDE 0100-551 (VDE 0100-551)
Low-voltage electrical installations, 
Part 5: Selection and erection of electrical equipment;
Chapter 55: Other equipment;
Section 551: Low-voltage generating sets

 

DIN VDE 0100-704 (VDE 0100-704)
Low-voltage electrical installations
Part 7-704: Requirements for special installations or locations - Construction and 
demolition site installations

 

DIN VDE 0100-100 (VDE 0100-100)
Low-voltage electrical installations
Part 100: Application area, purpose and principles

 

DVGW policy, technology notes, leaflet GW308
Mobile power generators for pipe construction sites

 

BGI 594, BG information:
The use of electrical equipment in case of increased electrical hazard

 

BGI 867, BG information:
Selection and operation of alternative power generators on construction and 
mounting sites

 

DIN 14687, firefighting and fire protection
Permanently installed generators (generating sets) < 12 kVA for the use in 
firefighting vehicles

Subject to change! The specified standards take into account the edition valid until 
01.2019 unless otherwise indicated.

Summary of Contents for B980853

























Reviews: