89000109-002
xVue Touch Installation Manual
Rev 2
Page 7-10
© Honeywell International Inc. Do not copy without express permission of Honeywell.
For Use in Non-Certified Aircraft
(18) From the KSD 100EXP PFD screen, verify the following:
(a) Verify the CDI source is set to “VOR1”, displayed in green.
(b) Verify the CDI CRS numeric value and CDI course pointer are both set to 100 degrees.
(c) Verify the CDI course deviation is centered with no left/right deflection.
(d) Verify the CDI Bearing Pointer 1 and Bearing Pointer 2 are both pointing to 100 degrees.
(19) On the KCP 100EXP, rotate the CRS knob until the CDI CRS numeric value and CDI course pointer
are both set to 105 degrees.
(20) From the KSD 100EXP PFD screen, verify the following:
(a) Verify the CDI source is set to “VOR1”, displayed in green.
(b) Verify the CDI course deviation is deflected left at the first deviation scale dot (5 degree
dot).
(21) On the KCP 100EXP, rotate the CRS knob until the CDI CRS numeric value and CDI course pointer
are both set to 110 degrees.
(22) From the KSD 100EXP PFD screen, verify the following:
(a) Verify the CDI source is set to “VOR1”, displayed in green.
(b) Verify the CDI course deviation is deflected left at the second deviation scale dot (10
degree dot).
(23) On the KCP 100EXP, rotate the CRS knob until the CDI CRS numeric value and CDI course pointer
are both set to 95 degrees.
(24) From the KSD 100EXP PFD screen, verify the following:
(a) Verify the CDI source is set to “VOR1”, displayed in green.
(b) Verify the CDI course deviation is deflected right at the first deviation scale dot (5 degree
dot).
(25) On the KCP 100EXP, rotate the CRS knob until the CDI CRS numeric value and CDI course pointer
are both set to 90 degrees.
(26) From the KSD 100EXP PFD screen, verify the following:
(a) Verify the CDI source is set to “VOR1”, displayed in green.
(b) Verify the CDI course deviation is deflected right at the second deviation scale dot (10
degree dot).
(27) On the Navigator, tune/activate the VHF radio to a valid LOC/ILS frequency.
(28) From the KSD 100EXP PFD screen, verify the following:
(a) Verify the CDI source is set to “LOC1”, displayed in green.
(b) Verify the CDI course deviation (left/right) is removed from the PFD CDI.
(c) Verify the Bearing Pointer 1 and Bearing Pointer 2 sources are set to “VLOC1”.
(d) Verify the CDI Bearing Pointer 1 and Bearing Pointer 2 are both removed from the PFD
CDI.
(29) On the VHF Radio Tester, set the mode to LOC/ILS, tune the same LOC/ILS frequency as displayed
on the Navigator (see step 27 above), and set both LOC DDM and G/S DDM to centered.
(30) From the KSD 100EXP PFD screen, verify the following:
(a) Verify the CDI source is set to “LOC1”, displayed in green.
(b) Verify the CDI course deviation is centered with no left/right deflection.
(c) Verify the Lateral and Vertical Deviation bars (near the attitude indicator) are both
centered with no left/right or up/down deflection.
(d) Verify the CDI Bearing Pointer 1 and Bearing Pointer 2 are both removed from the PFD
CDI.
