background image

 

Manual.

 RBJ Series of Rolling Bridge Jacks, 

Installation and Operation Manual

, Manual Part Number 5900004, 

Manual Revision A, Released May 2017. 

Copyright.

 Copyright © 2017 by BendPak Inc. All rights reserved. No part of this manual can be reproduced, 

adapted, translated, or transmitted by any means, electronic or mechanical, for any purpose or in any form, 

without prior written permission of BendPak Inc. 

Trademarks.

 BendPak and the BendPak logo are registered trademarks of BendPak Inc. All other company, 

product, and service names are used for identification only. All trademarks and registered trademarks mentioned 
in this manual are the property of their respective owners. 

Limitations.

 Every effort has been made to ensure complete and accurate instructions are included in this 

manual. However, product updates, revisions, and/or changes may have occurred since this manual was 

published. BendPak reserves the right to change any information in this manual without incurring any obligation for 

equipment previously or subsequently sold. BendPak is not responsible for typographical errors in this manual. 

Warranty.

 The BendPak warranty is more than a commitment to you: it is also a commitment to the value of 

your new product. For full warranty details and to register your new product, contact your nearest BendPak dealer 

or visit 

bendpak.com/support/warranty

Safety.

 Your new product was designed and manufactured with safety in mind. Your safety also depends on 

proper training and thoughtful operation. Do not set up, operate, maintain, or repair the unit without reading and 

understanding this manual and the labels on the unit. 

Owner Responsibility.

 In order to maintain your product properly and to ensure operator safety, it is the 

responsibility of the product owner to read and follow these instructions: 

•  Follow all setup, operation, and maintenance instructions. 

•  Make sure product setup conforms to all applicable local, state, and federal codes, rules, and regulations, 

such as state and federal OSHA regulations and electrical codes. 

•  Read and follow all safety instructions. Keep them readily available for operators. 

•  Make sure all operators are properly trained, know how to safely operate the unit, and are properly supervised. 

•  Do not operate the product until you are certain all parts are in place and operating correctly. 
•  Carefully inspect the product on a regular basis and perform all maintenance as required. 

•  Service and maintain the unit only with approved replacement parts. 

•  Keep all instructions permanently with the product and make sure all labels are clean and visible. 

 

 

Unit Information.

 Enter the Model Number, Serial 

Number, and the Manufactured On date from the label 

on your unit. This information is required for part or 
warranty issues. 

 

Model:  

 

 
Serial:  

 

 

Manufactured On:  

 

 

 

 

 

 

Summary of Contents for RBJ Series





















































Reviews: