XPR-10 Series Two-Post Lifts
46
P/N 5900951 — Rev. D — May 2019
5.
Moving to the Offside Post
, locate the Safety Assembly
without
the Safety Lock Release
Handle, a Safety Clevis Pin, two Springs, and one Cotter Pin.
6.
Put one of the Springs next to the head of the Safety Clevis Pin, then insert the Safety Clevis Pin,
from the left, through the hole in the left welded plate, then through the Safety Assembly, and then
through the right welded plate.
7.
Put the second Spring on the right end of the Safety Clevis Pin, then install the Cotter Pin.
The Safety Lock Cable connects the two Safety Assemblies together.
Note
: The Safety Cable should have been put into place earlier,
but not attached
at either end.
The following procedure describes how to hook up the Safety Cable on the Offside Post and
on the Powerside Post.
To connect the Safety Lock Cable
:
1.
Starting on the Offside Post
, bring the loop end of the Safety Cable down through the
inside
of the Offside Post.
2.
Pull the Safety Cable out to the outside of the Offside Post.
3.
Route it up and over the short, lower Welded Pin, past the Safety Clevis Pin, and loop it over the
right end of the longer, higher Welded Pin.
4.
Moving to the Powerside Post
, screw two Nuts and Washers onto the threaded end of the
Welded Pin with Threads. Make sure that one Nut and one Washer is on each side of the hole in
the Welded Pin with Threads.
5.
Bring the straight end of the Safety Cable down through the inside of the Powerside Post and pull
it out to the front of the Powerside Post.
6.
Put the straight end of the Safety Cable over the front of the Welded Pin and into the hole in the
Welded Pin with Threads, between the two Nuts and the two Washers.
7.
Pull any slack out of the Safety Cable, then tighten the Nuts.
When tightening the Nuts, keep tension on the Safety Cable and keep the Safety Cable centered
between the two Nuts.
8.
Operate the Safety Lock Release Handle, checking for proper operation of both Safety Assemblies.
⚠
DANGER
Make sure that both the Powerside and the Offside Safety Assemblies engage
properly
before
using the Lift.
Summary of Contents for XPR-10 Series
