XPR-10 Series Two-Post Lifts
63
P/N 5900951 — Rev. D — May 2019
Installing the Safety Covers
There are two Safety Covers, one for each Safety Assembly, on the outside of each Post.
Refer to
Installing the Safety Assemblies and the Safety Lock Cable
for more information
about installing the Safety Assemblies.
The Safety Covers are
not
interchangeable:
•
The Offside Safety Cover can be installed in either orientation. It does not have a slot.
•
The Powerside Safety Cover can only be installed in one orientation: there is a slot on the front for
the Safety Lock Release Handle and a hole on the left side for the Microswitch Cable.
By the time you get to this section of the installation, the Powerside Safety Cover will be in place
but not fully installed. The Powerside Safety Cover is in place already because both the Short
Hydraulic Line and the Microswitch Cable were routed through it on their way to the Power Unit.
Both Safety Covers connect to their Posts via blocks in the upper left and lower right corners.
To install the Safety Covers
:
1.
Locate the two Safety Covers and four Cover Screws.
2.
On the Offside Post
, install the Cover Screws in each block.
Do not fully tighten the Cover Screws into the block: there must be enough space between the
block and the Cover Screws to slide in the Safety Cover.
3.
Slide the Safety Cover into position, then fully tighten both Cover Screws into their blocks so that
the Safety Cover is held securely.
4.
On the Powerside Post
, install the Cover Screws in each block.
Do not fully tighten the Cover Screws: there must be enough space between the block and the
Cover Screws to slide in the Safety Cover.
5.
Make sure the Microswitch Cable and the Short Hydraulic Line are correctly routed through the
Powerside Safety Cover and the Safety Lock Release Handle is usable through the slot on the
front.
6.
Fully tighten both Cover Screws into their blocks so that the Safety Cover is held securely.
Lubricating the Lift
XPR-10 Series Lifts work better and longer if you keep them lubricated.
Lubricate the following:
•
Cable sheave pins, with WD-40 or equivalent.
•
Safety pins, with WD-40 or equivalent.
•
The four inside corners of both Posts, with light axle grease.
Summary of Contents for XPR-10 Series
