background image

 

11 

                                                                                                 

INSTRUCTIONAL MANUAL FOR BENEFIT   

ST3604 CONSOLE 

 

 

 

DISPLAY FUNCTION : 

 

ITEM DESCRIPTION 

SCAN 

. The sequence of display: TMR

SPD

 DST

CAL

PULSE 

. In SCAN mode, press MODE key to choose other functions. 
. Automatically scan through each mode in sequence every 6 seconds. 

SPEED (SPD) 

. W/O any signal been transmitted into the monitor for 4 seconds, SPEED 

will display “0.0” 

. Display current training speed. 

TIME (TMR) 

. W/O setting the target value, time will count up. 
. With setting the target value, time will count down from your target time to 

0, and as 0 is achieved time alarm. 

. W/O any signal been transmitted into the monitor for 4 seconds, time will 

STOP  

. Range 0:00 ~ 99:59 

DISTANCE (DST) 

. W/O setting the target value, distance will count up. 
. With setting the target value, distance will count down from your target 

distance to 0, and as 0 is achieved distance alarm. 

. Range 0.0~999.9 KM 

CALORIES (CAL) 

. W/O setting the target value, calorie will count up. 
. With setting the target value, calories will count down from your target 

calorie to 0, and as 0 is achieved calorie alarm. 

. Range 0.0~999.9 Cals 
.

 

Calorie count on the display only serves as a general guideline. For detail 

calorie consumption for each individual please consult a physician or a 
nutritionist. 

PULSE 

. With pulse signal into for 6 seconds, the current pulse will display. 
. W/O pulse signal into for 6 seconds, it displays “P” 
. Pulse alarm when over preset target pulse. 
. Range 0-40~240 BPM 

Summary of Contents for ESB440















Reviews: