background image

 

 

 
 
 
 
 
 
 
 
 
 
o Regularly check the tubing inside the peristaltic pump. Replace this hose immediately in 
case of leakage. It is advisable to replace this hose every 2 years as a precaution. 
 
o Regularly check the pH injection nipples for leaks. Replace these nipples immediately in 
case of leakage. 
 
o Check the power supply and cable connection regularly. If the pump begins to operate 
abnormally, turn it off and call a qualified technician. 
 

General visual condition 

Clear, free of algae and sediment 

Temperature  

Higher than 15° C 

pH 

Between 7.2 and 7.6 

Level of stabikisator (cyanic acid) 

Below 40 ppm (mg/L) 

Alkalinity 

Between 80 ppm and 120 ppm 

Hydrometric titer (TH) 

Below 60 °F 

Recommended salinity (for chlorinator) 

2-2.5 kg/m³ for LOW SALT equipment 

Concentration of free chlorine  

Between 0.5 and 1.5 ppm 

 
Warnings 
 

○ Improper installation can create an electrical or chemical hazard, which can result in 

serious injury.  
 

○ Never mix acid and liquid chlorine.

 

 

○ Keep the installation and chemicals out of the reach of children. Always wear safety gloves 

and safety glasses when working on the installation. 
 

○ Switch off the power supply

 

 

○ NEVER make any adjustments inside the dispensing equipment. 

 

 

○ If you are not familiar with the pool filter system and dosing equipment: 

 

- read the entire installation and operating instructions before using the dosing equipment; 
never modify anything without consulting your supplier, professional pool contractor. 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for ZPTX0010-P





























Reviews: