background image

 

 

 
 
 
 
 
 
 
 
 
 
Periodic maintenance 
 

Material 

Tasks 

Frequency 

Pool filter circuit 

Cleaning the filters 

Regularly 

Technical room 

Check that the nozzles are pointed slightly 
downward 

Regularly 

Electrical box 

Check all features listed in the precautions 
section 

Regularly 

Cell 
 

Check the metal parts for oxidation 

Regularly 

Check the tightness of the electrical connections 

As soon as water 
temperature is below 15 
°C 

pH injection 

Make sure that the electrolysis is stopped 

Min 1 time per year 

 

Replace the flexible internal hose of the 
peristaltic pump 

 

pH pump 
 

Replace the check valve on the injection 
connection 

Regular 

 

Once per year 

ORP probe  

Ensure that the suction bulb is always immersed 
in water or appropriate CIP. 

At each commissioning  

 
Troubleshooting for the blue steering box 
 

PROBLEM

 

CAUSE

 

SOLUTION

 

Screen does not illuminate 

No voltage present 

Verify voltage 

Booster pump does not dose 
 

Switch under the dosing pump is 
set to "O". 

Set switch to "1 

Settings of pH control are wrong: 
pH+ while pH- is dosed (or vice 
versa) 

Verify settings 

A level detector is connected and 
gives a wrong contact 

Disconnect level detector 

A flow switch is connected and 
indicates that there is no flow. 

Verify flow and flow switch (go to 
setting flow switch : no) 

Acid pump keeps dosing 
 

Setpoint not yet reached 

No action required 

Wrong parameter set: pH+ while 
pH- is dosed (or vice versa) 

Correct parameter. 

Summary of Contents for ZPTX0010-P





























Reviews: