18
16) MESSAGGI DI ERRORE
Di seguito sono elencati alcuni messaggi che vengono visualizzati dal display in caso di anomalie di funzionamento:
err
Errore ingressi N.O. (autoset)
Se l’errore si presenta in fase di autoapprendimento controllare lo stato degli ingressi PP/PED/
OPEN/CLOSE.
Err1
Errore STOP (autoset)
Intervento di STOP durante autoset.
Err2
Errore fotocellule (autoset)
Intervento di PHOTO/PHOTC durante autoset.
Err4
Errore bordo sensibile (autoset)
Intervento BAR durante AUTOSET.
Err5
Errore fototest
Verificare il funzionamento ed il corretto collegamento delle fotocellule.
amp
Intervento amperometrica
Un ostacolo o un punto di attrito ha provocato l’intervento del sensore ampertometrico. Rimuo-
vere l’ostacolo o verificare la corsa dell’anta.
F01
Il freno collegato assorbe troppo.
F02
Corto circuito sul motore. Verificare impedenza degli avvolgimenti e l'isolamento fra ciascuna
fase del motore e la massa.
F04
All'accensione la tensione di bus non rientra nelle specifiche. Verificare la tensione di alimentazione,
o la corretta selezione del motore secondo il menù
MOT
.
F05
Rilevata sovratemperatura nella centrale.
F06
Superata soglia corrente istantanea. Sbloccare il motore e verificare che il pignone sia libero di
girare. Contattare eventualmente l'assistenza tecnica.
F07
Superata soglia corrente ritardata. Sbloccare il motore e verificare che lungo tutta la corsa del
cancello non ci siano carichi eccessivi (difficoltà nel movimento). Contattare eventualmente l'as-
sistenza tecnica.
F08
Superata massima tensione ammessa sul bus di potenza. Verificare la tensione di alimentazione.
Eseguire nell'ordine indicato le seguenti azioni:
1. Aumentare parametri
TDEC
e
TSMO
/
TSMC
, verificare arresti intermedi con comandi di
STOP
/
PP
/
PHOT
/
BAR,
se si ripresenta il problema passare al punto seguente:
2. Aumentare parametro
TBR
, verificare arresti intermedi con comandi di
STOP
/
PP
/
PHOT
/
BAR
, se si
ripresenta il problema passare al punto seguente:
3. Collegare resistenza di frenatura, verificare arresti intermedi con comandi di
STOP
/
PP
/
PHOT
/
BAR
,
se si ripresenta il problema passare al punto seguente:
4. Diminuire i parametri
FSTO
/
FSTC
, verificare arresti intermedi con comandi di
STOP
/
PP
/
PHOT
/
BAR
.
F09
I valori impostati non sono corretti e l'anta procede oltre il finecorsa.
Agire modificando, nell'ordine, i seguenti parametri:
-
blo
/
blc
(diminuire)
-
tsmo
/
tsmc
(aumentare)
-
sldo
/
sldc
(diminuire)
-
fsto
/
fstc
(diminuire)
17) DISPLAY LCD
Nel caso sia necessario, è possibile ruotare di 180° la visualizzazione del display LCD:
-
Togliere alimentazione di rete
-
Premere PGM
-
Mantenendo premuto PGM, ripristinare l’alimentazione di rete
-
Mantenere premuto PGM (circa 5s) fino alla comparsa della versione software, ruotata di 180°.
Procedere normalmente con la programmazione.
18) DIAGNOSTICA
Nel caso di anomalie di funzionamento è possibile visualizzare, nel display,lo stato di tutti gli ingressi (finecorsa, comando e sicurezza). Ad ogni ingresso
è associato un segmento del display che in caso di attivazione si accende, secondo il seguente schema.
PHOTO
SWC
STOP
SWO
PHOTC
BAR
P.P.
PED
OPEN
CLOSE
Gli ingressi N.C. sono rappresentati dai segmenti verticali. Gli ingressi N.O. sono rappresentati dai segmenti orizzontali.
LD1 LED: Presenza alimentazione di rete.
LD2 LED: PR 5V
PHOTO: PHOT1/TST1
PHOTC: PHOT2/TST2
F4: Fusibile protezione linea alimentazione 15AT.