8
Remote Learning In Receivers Built Into The Control Units
Proceed as follows:
•
Press the hidden key of the transmitter saved (the red LED on the transmitter flashes)
•
Press within 5 seconds the key on the previously memorized transmitter corresponding to the channel to associate with the
new transmitter.
•
Press the hidden key of the transmitter saved (the red LED on the transmitter flashes)
•
Within 5 seconds, press the key of the new transmitter to be associated with the selected channel.
•
The receiver exits the programming mode, check the proper operation of the new transmitter saved.
The procedure can be summarized as follows:
-Hidden key of the currently active transmitter (T1 +T2 for 3s)
-Key of the transmitter already operative with the function to duplicate (within 5s)
-Hidden key of the new transmitter (T1 +T2 for 3s)
-Key of the new transmitter (5s)
Notes:
S ome controllers signal the various learning phases via the assistive or the flashing light.
Remote learning is only possible with ARC and HCS transmitter, and is not possible with programmable code transmitters.
For security reasons, remote learning is prevented during motor opening/closing.
In some cases, the procedure must be performed with the doors fully opened; consult the deviceʼs instructions..
TO. GO/HAPPY AK CLONEABLE
AK series transmitters can be programmed with the same code as a programmable transmitter or K or P series, already stored in
a system, or to replace most fixed-code transmitters on the market with a simple and fast procedure without the need to access
the receiver nor to open the remote control.
An important innovation featured by these new AK versions is the implementation of double-encoding, ARC or fixed: this transmit-
ter can be used as a normal cloneable transmitter or as a real ARC transmitter with variable code. In fact, the AK radio control,
if not used to clone a fixed code transmitter, sends the code by default with Advanced Rolling Code encoding. The only way to
make it use the fixed-code is to program it starting from TO.GOWP or TO.GOWK.
Quick cloning
In quick cloning you get a transmitter that replicates exactly every single channel of the original transmitter in the new TO. GO/
HAPPY AK; we recommend using a 2AK to clone a two-channel original transmitter and a 4AK to clone a four-channel transmitter.
Proceed as follows:
1) press and hold the key T1 of the new transmitter AK. When pressing T1, the LED lights up steadily, after 5 seconds it will begin
to flash rapidly, after 15s to flash slowly.
2) after about 15s, put the original transmitter near the new transmitter as shown in the picture, and continue
to hold the key T1 on the new remote control, and press any button on the original remote control.
3) if the procedure was completed successfully, the LED of the new transmitter AK will turn off. Release all the
keys pressed.
All channels of the original TO.GO(HAP PY are replicated on the AK.
N.B .: Use for both remote controls batteries charged.
If after 15 sec. the red LED on the new transmitter is not off, release the buttons of the remote control and
after 1 minute, repeat from step 1, being careful to place the original transmitter as shown in the picture.
Advanced cloning
In advanced cloning you can choose which channel of the original transmitter will be replicated on the AK.
For example, you can replicate channel 3 of an old transmitter on channel 1 of a AK, which is not possible
during quick cloning.
Proceed as follows:
1) on the new AK, press and hold the key of which you want to replicate the function of the original. When you
press the button, the LED lights up steadily, after 5 seconds it will begin to flash rapidly.
2) after 5s, put the original transmitter near the new transmitter as shown in the picture, and continue to hold
the key on the new remote control, and press the button of the original remote control whose code you intend
to copy.
3) if the procedure was completed successfully, the LED of the new transmitter AK will turn off. Release all the keys pressed.
The channel chosen in the original TO.GO/HAPP Y is now replicated in the new AK.
N.B .: Use for both remote controls batteries charged.
If after 30 sec. the red LED on the new transmitter is off, release the buttons of the remote control and repeat from step 1, being
careful to place the original transmitter as shown in the picture.
T1
T1
T2
T1
T1
T2
TX 1
TX 1
TX 2
TX 2
>
