background image

Bennett 621 Interconnection Box Instruction & Service Manual 

Product Introduction

 

TS2 - TS5 (POSITIONS 1-8)   DISPENSER COMMUNICATION 

Terminal blocks TS2 through TS5 are labeled as (Positions 1 - 8) that are used for Fueling Points 1 through 16. Each terminal strip position will 
supply two fueling points one (+) positive and one (–) negative connection. 

Note: 

A fueling point is one side of a dispenser and a two-sided 

dispenser would have two fueling points.  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TS6 - TS7 (POSITIONS 9-12)  DISPENSER COMMUNICATION  

Terminal block TS6 - TS7 (Positions 9-12) are used for Fueling Points 17 through 24. Each terminal strip position will supply two fueling positions 
one (+) positive and one (–) negative connection. 

Note: 

A fueling point is one side of a dispenser and a two-sided dispenser would have two fueling 

points.  

TERMINAL POSITION 

FUELING POINT 

COLOR 

PIN 

17 & 18 

Orange 

(+) positive 

17 & 18 

Yellow 

(-) negative 

10 

19 & 20 

Orange 

(+) positive 

19 & 20 

Yellow 

(-) negative 

11 

21 & 22 

Orange 

(+) positive 

21 & 22 

Yellow 

(-) negative 

12 

23 & 24 

Orange 

(+) positive 

23 & 24 

Yellow 

(-) negative 

13 

NOT USED 

Orange 

(+) positive 

NOT USED 

Yellow 

(-) negative 

14 

NOT USED 

Orange 

(+) positive 

NOT USED 

Yellow 

(-) negative 

15 

NOT USED 

Orange 

(+) positive 

NOT USED 

Yellow 

(-) negative 

16 

NOT USED 

Orange 

(+) positive 

NOT USED 

Yellow 

(-) negative 

LEDs 

DISPENSER & POS COMMUNICATION 

The 621 Circuit Board has surface mount LEDs that are used for troubleshooting. If the console and dispensers are communicating, all LED’s will be 
flashing. If not communicating with the POS or Dispenser then the “Transmit” LED will be on constantly and the “Receive” LED will be off. Refer to 
the troubleshooting section for more information.

 

 
 
 
 
 

 

 

TERMINAL POSITION 

FUELING POINT 

COLOR 

DESCRIPTION 

1 & 2 

Orange 

(+) positive 

1 & 2 

Yellow 

(-) negative 

3 & 4 

Orange 

(+) positive 

3 & 4 

Yellow 

(-) negative 

5 & 6 

Orange 

(+) positive 

5 & 6 

Yellow 

(-) negative 

7 & 8 

Orange 

(+) positive 

7 & 8 

Yellow 

(-) negative 

9 & 10 

Orange 

(+) positive 

9 & 10 

Yellow 

(-) negative 

11 & 12 

Orange 

(+) positive 

11 & 12 

Yellow 

(-) negative 

13 & 14 

Orange 

(+) positive 

13 & 14 

Yellow 

(-) negative 

15 & 16 

Orange 

(+) positive 

15 & 16 

Yellow 

(-) negative 

FUEL CONTROLLER COMMUNICATION 

LED 

FUNCTION 

D1 (WT) 

POS GCL Transmit 

D2 (WR) 

POS GCL Receive 

DISPENSER COMMUNICATION 

LED 

FUNCTION 

D3 (BT) 

Bennett Transmit 

D4 (BR) 

Bennett Receive 

Summary of Contents for 104080























Reviews: