BenQ RM5501K Installation Manual Download

Page: 15 / 17

PC Get-function command to LCD Monitor

Value Range (ASCII Bytes)

Get Function

Len

Cmd

Type

Cmd Code

(Hex)

RS232

LAN

Model Info

(1) Input value: Byte1 - Byte2 -

Byte3…Byte15

Byte2~Byte11=0x00

Byte1=0x01: Get Customer Name

Byte1=0x02: Get Customer Model Name

Byte1=0x04: Get Scaler Firmware Version

Byte1=0x06: Get Serial Number

(2) Return value: Byte1 - Byte2 -

Byte3…Byte15

The Byte1 value at the return value should be the same as the

value of Byte1 at input value.

Byte2~Byte15 should be ASCII format.

Ex: If Customer=Generic, Byte1=0x01, Byte2='G',

Byte3='e',...Byte8='c', Byte9~Byte11=0x00.

Ex: If the Scaler Firmware Version=1.02, Byte1=0x03, Byte2='1',

Byte3='.', Byte4='0', Byte5='2', Byte6~Byte11=0x00.

Signal Status

000: Signal unstable

001: Signal stable (Active Sync exists)

Volume

000 ~ 100

Mute

000: Off

001: On

Button&IR Control

000: Disable

001: Enable

Video Source

000 : VGA

001 : HDMI1

002: HDMI2

021 : HDMI3

022 : HDMI4

101 : android

102 : OPS

Power

000 : Monitor Off

001 : Android

001 : Monitor On

002 : Android

Summary of Contents for RM5501K


















Search results

Summary of Contents for RM5501K

Reviews:

Related manuals for RM5501K

Brands by name

Popular brands

BenQ RM5501K, Installation Manual

Search results

Summary of Contents for RM5501K

Reviews:

Related manuals for RM5501K

Brands by name

Popular brands