Beretta 20184340 Installation Manual Download

Page: 10 / 16

INSTALLATION

11 WATER CONNECTIONS

During installation, pay attention to the position of the probe with respect to the collector. The collector probe must

always be in the upper section of the panel as indicated in the figures below.

Union

sensor

pocket

seal ring

toward the

heat transfer

circuit

seal ring

from the

heat transfer

circuit

When tightening a fitting,

HOLD THE OPPOSITE

FITTING STEADY WITH

A SECOND TOOL

to avoid damage

seal ring

Plug

captive nut

seal ring

Plug

captive nut

seal ring

Union

captive nut

When tightening a fitting,

HOLD THE OPPOSITE

FITTING STEADY WITH

A SECOND TOOL

to avoid damage

sensor

pocket

toward the

heat transfer

circuit

from the

heat transfer

circuit

captive nut

Ring

nut

seal ring

captive nut

Ring

nut

seal ring

captive nut

Ring nut

seal ring

insulated connector

pipe

seal ring

Plug

HORIZONTAL CONFIGURATION

VERTICAL CONFIGURATION

Summary of Contents for 20184340

















Search results

Summary of Contents for 20184340

Reviews:

Related manuals for 20184340

Brands by name

Popular brands

Beretta 20184340, Installation Manual

Search results

Summary of Contents for 20184340

Reviews:

Related manuals for 20184340

Brands by name

Popular brands