background image

 

4

 

PROXIMITY TO SIDE CABINET INSTALLATION 

1.

 This rangetop may be installed directly adjacent to existing 36" (91.5 cm) high base cabinets. IMPORTANT: The top 
grate support MUST be 3/8" (.95 cm) above the adjacent base cabinet countertOP. 

2.

The rangetop CANNOT be installed directly adjacent to sidewalls, tall cabinets, tall appliances, or other side vertical 
surfaces above 36" (91.5 cm) high. There must be a minimum of 6" (15.2 cm) side clearance from the rangetop to 
such combustible surfaces above the 36" (91.5 cm) counter height. 

3.

3. Within the 6" (15.2 cm) side clearance to combustible vertical surfaces above 36" (91.4 cm) I the maximum wall 
cabinet depth must be 13" (33.0 cm) and wall cabinets within this 6" (15.2 cm) side clearance must be 18" (45.7 cm) 
above the 36" (91.4 cm) high countertop. 

4.

4. Wall cabinets above .the rangetop must be a minimum of 36" (91.4 cm) for the open top burner models and a 
minimum of 42" (106.7 cm) for the sealed burner models above the rangetop cooking surface for the full width of the

 

rangetop. This minimum height requirement does nQ1 apply if a rangehood is installed over the cooking surface. 

 
 

 

 

 

 

 

 

 

 

 

 

 

 

A 6”(15.2cm) 

MIN 

B 36”(91.5cm) 
C 36”(91.5cm) 
D 13”(33.0cm)MAX 
E 18”(45.7cm)MIN 
F 36”(91.5cm)

 

G 6”1/2(16.5cm) 
H 1”(2.5cm) 

MIN 

i 9/16” 

(1.8cm) 

2”( 5 cm) MIN

 

120 VAC/60 Hz withing 
48” (122.9cm) of right 
rear or rangetop 

Summary of Contents for CB36500X















Reviews: