Installation Instructions for 83KW/93KW–85KW/95KW IDH Max Cylindrical Locks
BEST ACCESS SYSTEMS
Indianapolis, Indiana
2
Components checklist
Site survey
Use the following survey to record information about the
installation site. You need this information to determine
field wiring needs, select a power supply, and determine
how to prepare the door for the lock.
Lock information
Lock function:
❑
DDEL–Electrically locked
❑
DDEU–Electrically unlocked
Power source for lock:
❑
Separate power supply
❑
Power provided through panel interface module
Power source for panel interface module:
❑
Separate power supply
❑
Power provided through access control panel
Distance of lock site from lock power source: feet
Distance of lock site from panel interface module site:
feet
Door information
Door handing and bevel:
❑
Left hand (LH)
❑
Left hand, reverse bevel (LHRB)
❑
Right hand (RH)
❑
Right hand, reverse bevel (RHRB)
Door thickness: inches (1 3/4
″
– 2 1/4
″
; 1 3/8
″
with
spacer)
Environment information
Ambient temperature:
❑
Is within specifications. See the tables below.
This product meets the following Locked Door Outdoor
test requirements for ANSI/BHMA 156.25:
This product meets the following Full Indoor test
requirements for ANSI/BHMA 156.25:
Side of door
Range
Inside
+66°F to +74°F (+19°C to +23°C)
Outside
–31°F to +151°F (–35°C to +66°C)
Side of door
Range
Inside and outside
+32°F to +120°F (0°C to +49°C)
Use the following checklist to make sure that you have the
items necessary to install the components provided with
your 83KW/93KW–85KW/95KW IDH Max Cylindrical Lock.
Components provided in the box:
❑
Chassis with outside knob/lever and outside rose liner
assembly
❑
Inside escutcheon assembly with field wire harness
❑
Inside escutcheon access door
❑
Inside rose liner with RQE feature
❑
Outside escutcheon assembly
❑
Inside knob/lever
❑
Throw member package
❑
Latch
❑
Door status switch & magnet assembly
❑
Plastic bushing package
❑
Hub washers
❑
Trim hole insert package
❑
Escutcheon screw package
❑
Panel interface module
❑
Strike package
❑
Bar code ID sticker (for your records)
Other items you’ll need:
❑
Power supply for one IDH Max Cylindrical Lock (if
you’re providing a separate power supply): regulated;
12 volts DC at .85 amps
Note:
If you intend to power more than one lock with the
same power supply, calculate the amperage for the
power supply by multiplying .85 by the number of
IDH Max Cylindrical Locks (1.1 by the number of IDH Max
Mortise Locks).
❑
Power supply for the panel interface module (if you’re
providing a separate power supply): 12 volts DC at
.1 amp
❑
Wire transfer hinge: 8 conductors min.; 28 AWG min.
continued
Summary of Contents for 34HW
