background image

42-1/2" long 2x3

61" long 2x3

Install trim boards with 8d galvanzied box nails spaced 12" apart.

Step 21

Install Front Gable Overhang

1.

Install (2) two 61" and (2) two 42-1/2" long 2x3s

against the roof sheathing; screw the sheathing to the
2x3s with 1-5/8" long screws. Important: the roof
sheathing should extend 3/4" beyond the 2x3s to receive

the 1x4 gable trim installed later.

2.

Install (2) two 4-1/2" long 2x3s, at the bottom, between

the 43-1/2" 2x3s.

4-1/2" long 2x3 Block

Ends With Blue Mark

3. Install (2) two 1x4-61" gable trim boards, with the ends marked

with a blue line together at the ridge.

Sheathing

Extends 3/4"

4. Install (2) two 43-1/2" long 1x4 trim boards

on the sides.

5.

Cut to fit 7-1/2" wide soffit panels under the

overhang.  Use 6d galvanized nails.

6.

Install 35-3/4" long 1x3 trim boards flush

with each side of the loft door opening.
Install a 50" long trim board across the top.
If door opening is cut out the siding will
extend 3/4" below the top trim board.

7.

Install loft doors using 4" hinges and 1-1/4"

long black screws. Install a 4" barrel bolt to
the back of the right door using 1-1/4" black
screws.  Drill a hole for the round shaft to
drop into.

Summary of Contents for Millcreek

























Reviews: