background image

Problems

The Wi-Fi setup is not 

successful

Probable Causes

Solutions

The pump has been connected to the 

wrong band

If the router your pump is connected to is dual-band and currently not 

connecting to a 2.4GHz network, please switch to another band of the 

same router (2.4GHz) and try to pair pump heater again. 5GHz networks 

are not supported.

The spa pump location is too far from 

the router.

Set up the wrong Network Name

Start the connection procedures again and be sure that the network 

name is typed correctly.

The Wi-Fi password used

during the connection is wrong

Start the connection procedures again and be sure that the password is 

correct.

The strength of the Wi-Fi signal is not 

stable

1. Check if the router works correctly.

2. Go near the spa and check the signal on your phone. In case the 

signal strength is not stable, check the condition of your router. In case 

the signal strength is full, repeat the operation to connect the spa to 

the network.

There is an appliance near the spa 

pump or the router that creates Signal 

Interference

The Wi-Fi connectivity can be interrupted by  electromagnetic or other 

interferences. Keep the appliance away from other electronic devices 

that may cause interferences.

Your phone will not connect to the Wi-Fi 

network during the registration

Check if the mobile device is in airplane mode.

Make sure to have the airplane mode deactivated when connecting to 

the Wi-Fi network.

APP Feedback

Consult the help section in the APP for extensive and up-to-date 

troubleshooting tips.

Check with your cell phone to see if there is full Wi-Fi signal.In case the 

strength of the signal on your phone is too low, check where the strength 

of the Wi-Fi signal is full and place the spa in that position.

Indicator light is on

Indicator light flashes quickly

Indicator light is off

Indicator light flashes slowly

Connected to the router

Lost Wi-Fi signal

Light damaged & Wi-Fi module has 

problem

Waiting to connect to the router

The pump already connected to your phone

Check the status of your router. The spa lost the Wi-Fi signal.

For more information, please visit the support section on 

our website, www.bestwaycorp.com.

The pump is ready to connect to your phone

Wi-Fi LED Status

29

Summary of Contents for Lay-Z-Spa HAVANA AIRJET PLUS

































Reviews: