BETAFPV Lite brushed V2 FC User Manual Download | Manualshive

Page: 16 / 16

background image

15

9.DEVELOPMENT

Contribution of bug fixes and new features is encouraged. All the source code for the
flight controller and OSD is open in Github.

；

Source code of the flight controller:

https://github.com/BETAFPV/LiteSilverware

Source code of the OSD:

https://github.com/BETAFPV/LiteOSD

The programmer ports for the FC MCU STM32F042G6U6 and OSD MCU
EFM8BB21 are showed as below.

STM32F042 is the processor of FC and a STM32 programmer is needed to flash the
firmware through the SWD port (CLK, SWDIO) of the controller. We would
recommend the ST-LINK or BeeLink USB Flasher.
EFM8BB21 is the processor of OSD. You need a efm8 programmer to upload the
firmware through the C2 port (C2CK, C2D) of the controller. We would recommend
the Silicon Lab debug adapter.

«
...
14
15
16

Summary of Contents for Lite brushed V2 FC

















Reviews:

No comments

Related manuals for Lite brushed V2 FC

Brand: Manfrotto Pages: 2

Brand: Manfrotto Pages: 2

Brand: Balboa Pages: 2

Brand: KBS Pages: 37

Brand: A-Tach Mounts Pages: 2

Brand: A-Tach Mounts Pages: 2

Brand: A-Tach Mounts Pages: 2

Brand: Veeniix Pages: 44

Brand: Abibird Pages: 2

Brand: Abicor Binzel Pages: 20

Brand: Darfon Pages: 28

Brand: VanEssa mobilcamping Pages: 8

Brand: NavLinkz Pages: 4

IO-Link BAE SA-CS-027-YI-BP00,3 GS04

Brand: Balluff Pages: 50

Brand: Ericsson Pages: 487

Ocean Seven 304Plus

Brand: idronaut Pages: 79

Brand: Zacuto Pages: 2

Brand: Iget Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands