background image

4

Operating Instructions for Commercial Spotter

WARRANTY

To protect your investment, promptly fill in 

the required information on the warranty card included 

with the unit. Then mail the card back. 

WHEN THE MACHINE IS DELIVERED…

BEFORE USING THE MACHINE

GENERAL PRECAUTIONS

Read the manual carefully and completely before 

attempting to operate the unit. This manual has 

important information for the use and safe operation of 

this machine. Keep this manual handy at all times. The 

commercial spotter will provide years of satisfactory 

service if operated and maintained according to 

recommendations in the manual.

FFoolllloow

w  tthheessee  gguuiiddeelliinneess  ttoo  eennssuurree  ooppeerraattoorr  

ssaaffeettyy  aanndd  ttoo  m

maaiinnttaaiinn  eeqquuiippm

meenntt  iinn  rruunnnniinngg  

oorrddeerr..  

Make sure the machine is plugged into an electrical 

outlet with the same voltage rating as shown on the 

nameplate of the machine. Do not attempt to plug a 

115 volt machine into a 230 volt outlet or a 230 volt 

machine into a 115 volt outlet. 

WARNING

Do not expose the machine to freezing tempera-tures.
Do not use the machine for totally dry vacuum-ing. 

This machine is not fitted with a fine dust filter.
Do not use citrus-based cleaners in this machine.
Do not use cleaning chemicals in this machine except 

those recommended for commercial extraction 

equipment. The use of any chemical with abrasive 

additives voids the warranty.
Do not break off or pull out the ground prong on the 

plug.
Do not attempt repair on a warranted machine unless 

instructions to perform it by an authorized shop are 

obtained from the factory.
Do not use any replacement parts except those 

specified on the parts list. Proper performance of the 

machine could be affected if substitutions are made.
Use defoamer at all times to prevent damaging the 

vacuum motor.
Do not use water in excess of 140° F (62° C). 

FFaaiilluurree  ttoo  ccoom

mppllyy  w

wiitthh  tthhee  aabboovvee  w

waarrnniinngg  

iinnssttrruuccttiioonnss  w

wiillll  vvooiidd  tthhee  w

waarrrraannttyy..

Disconnect the power cord from the outlet before 

attempting maintenance or repair work.

Do not leave machine connected to an electrical outlet 

when unattended.

Never pull the machine by the cord or yank the cord 

from the receptacle. Replace a damaged cord 

immediately.

If an extension cord is necessary, use a three 

conductor grounding cord – 12 gauge wire or heavier 

to prevent motor burnout and 

over-heating of wires.
To avoid electric shock, do not expose to rain. Store 

indoors.
To avoid fire, do not use machine in environ-ments 

where combustible liquids, vapors or dust 

concentrations are present.

Check the carton carefully for signs of rough handling. 

Remove the machine from the carton. If the machine is 

damaged, notify the carrier immediately and request an 

inspection. Be sure to keep the carton, packing inserts, 

packing lists and carrier receipt until the inspector has 

verified your claim. Liability ceases when the shipment 

is picked up by the carrier, but our  customer service 

staff will be glad to furnish any  information needed in 

connec-tion with the claim and will expedite the repair 

of the machine.

Summary of Contents for E88049-00













Reviews: