background image

Control Panel Function

Control Panel Function

Power Button

Radio Station Storage

Press the Power button to activate the control panel, the top

When the radio is on and you have found the station required

light will come on

press the M button to store this station
When the radio is on press and hold the M button, the radio 
will search for available stations, press M to store

Top Light

The light will be on when the control panel is powered up, to

Volume

turn on and off press this button, symbol will appear

Press the volume button, then press
the + or - button to change the volume
of the active function

Background Light

Not available on this model

CD Function

Press the FM/CD button until the CD symbol is displayed on 

Fan

the screen.

Press the fan button to activate the extraction fan, flashing 

You will need to connect an external CD player to the CD

symbol will appear

line from the cabin and place the player outside the cabin

Telephone

Alarm

With cabin telephone cable attached to your house landline

Press the alarm button to activate the audible alarm

connection, when a call is received the radio will turn off,

when the alarm is activated, the lights and fan come on

the symbol will flash on the screen .

and the alarm will sound

To answer the call press the telephone button.
To end the call press the button again.

Radio

Press FM/CD button until radio station  frequency
is shown and radio is on
To change station press "TUN" button, then press + or - to
adjust

SEPT  18 - V6BB

Summary of Contents for 900 Quadrant Steam



















Reviews: