Beuchat Mundial 3, User Manual

20

© 2002 Design, 2014

Doc. No. 12-5372-r01 (4/23/14)

User Manual

Set Water Type, 

information includes (Fig. 36):

>   Graphics TYPE and H2O.

>   Graphic SEA (or FrESH), flashing upon access.

•   A or M (< 2 sec) - to toggle between SEA and FRESH.

•  S (2 sec) - to step back to Set Wet Activation.

•   S (< 2 sec) - to save the setting and access Set Backlight Duration.

Set Backlight Duration, 

information includes (Fig. 37):

>   Graphics GLO and durA.

>   Time (min:sec) flashing upon access, with TIME icon.
•   A (< 2 sec) to step upward through Set Points of 0:05, 0:10, 0:30, 1:00 (min:sec) one at a time.

•   M (< 2 sec) to step back through the Set Points one at a time. 

•  S (2 sec) - to step back to Set Water Type.

•   S (< 2 sec) to save the setting and access Set DSD.

Set DSD (Dive Start Depth), 

information includes (Fig. 38):

>   Graphic DSD.

>   Depth flashing upon access, with FT (or M) icon.
•   A (< 2 sec) to step upward through the Set Points of 0,6 , 1,2 , 1,8 M (2 , 4 , 6 FT) one at a time.

•   M (< 2 sec) to step back through Set Points one at a time. 

•  S (2 sec) - to step back to Set Backlight Duration.

•   S (< 2 sec) to save the setting and access Set BDSI.

Set BDSI (Between Dive Surface Interval), 

information includes (Fig. 39):

>   Graphic BDSI.

>   Time (min:sec) flashing upon access, with SURF and TIME icon.

s

•   A (hold) to scroll upward through the Set Points 8 per second from 0:01 to 1:00 (min:sec) in increments of :01 (1 sec).

•   A (< 2 sec) to step upward through the Set Points one at a time.

•   M (< 2 sec) to step back through the Set Points one at a time.

•  S (2 sec) - to step back to Set DSD.

•   S (< 2 sec) to save the setting and revert to Set Utilities Lead-in.

------------------------------------------------------------------------------------------------------------------------------------------------------------

SERIAL NUMBER (SN)

• A (< 2 sec), while viewing Set Utilities Lead-in, - to access the Serial Number screen.

Information includes (Fig. 40): 

>   Graphic SN.

>   Factory programmed Serial Number (up to 6 digits). 

>   Firmware (operating software) revision number (e.g., graphic r1A).

•   A (< 2 sec) - to step forward to Chrono Lead-in.

•   M (< 2 sec) - to step back to Set Utilities Lead-in

•  M (2 sec), or 2 minutes of no button action, will revert to SURF MAIN.

•  L (< 2 sec) - to toggle the Backlight On/Off.  

Will be On for the duration time set.

•  L (2 sec), while the Backlight is On, - to reset the timer to keep it On for the full duration time set.

This information will be required if a unit is sent to Beuchat for evaluation or service.  Record it in the table 

provided in the back of this manual, and retain the sales receipt.

------------------------------------------------------------------------------------------------------------------------------------------------------------

CHRONOGRAPH

The Chrono in FREE Mode is the same one used in Watch Mode and it carries over between modes when it is in operation.

Refer to Watch Mode (page 12) for operation and displays.

Chrono Lead-in, 

information includes (Fig. 41):

>  Graphics GoTo Chro.

•  S (< 2 sec) - to access Chrono Status.

•  A (< 2 sec) - to step forward to SURF MAIN.

•  M (< 2 sec) - to step back to SN.

•  M (2 sec), or 2 minutes of no button action, will revert to SURF MAIN.

•  L (< 2 sec) - to toggle the Backlight On/Off.  

Will be On for the duration time set.

•  L (2 sec), while the Backlight is On, - to reset the timer to keep it On for the full duration time set.

Fig. 39 - SET BDSI

Fig. 38 - SET DSD

Fig. 40 - SN

Fig. 41 - CHRONO 

LEAD-IN

Fig. 37 - SET BACKLIGHT

DURATION

Fig. 36 - SET WATER 

TYPE