background image

18

Trouble description

Possible origins

Remedies

Rope is hardly
spooling off

• Wrong setting of the pull force
• Damaged rope
• Damaged brake band (collar)

• Seilauszugskraft nachstellen

• Seil wechseln
• Bremsband wechseln

The rope reels in even 
if the clutch is released

• Wrong setting of the clutch 
cylinder hub  
• Drum is damaged
• Clutch discs are damaged
• Driving chains excessively 
stretched

• Adjust cylinder hub

• Replace drum 
• Change clutch

6.   REPAIRS AND 
 

MAINTENANCE 

Make sure that the machine is fully disconnected and 

all moving parts are secured before performing any 

maintenance/repair work on the machine.

6.1    Periodic maintenance

Before starting to work with your winch, make sure to perform the fol-

lowing visual inspections:
• Make sure that all screws and nut are tight 

• Check for mechanical damages to the winch chassis 

• Make sure that all locking pins and rings are in place 

• Check for PTO shaft correct installation and connection and make 

sure that safety shield and chains are duly in place.

• Check the lower hitch points of the tractor and make sure they are 

firmly secured (no cross, horizontal movement).

• Check for clutch proper setting, check the brake and the rope pull 

out force

• Make sure to fix any anomaly or problem before starting to work. 

Perform the following maintenance works when needed and carry out 

periodic checkup: 
•  Hydraulic oil level control: if leaks are detected check the tightness 

of the remaining system (hoses and fittings) before continuing

• Lubricate all moving parts as needed  

Summary of Contents for FSW 5.5 H Evolution

































Reviews: