background image

26

12.  LEGAL WARRANTY

All BGU machines are covered with warranty terms in accordance with 

the law. Customers should promptly notify the manufacturer eventual 

material or production claims on their detection. While asking for war-

ranty service, customer should show copy of their purchase invoice or 

receipt. The warranty does not cover for faults due to natural wear, 

temperature or weather agents as well as misuse, faulty installation 

or set-up, improper operations and lubrication or act of vandalism. No 

warranty will be given on parts damaged by improper handling, use 

and application. The manufacturer is further not responsible for war-

ranty service on machines used for other applications as mentioned

in this manual, altered or modified by the customer or other thirds, or 

overloaded. 

No warranty applies to consumable parts (for instance: V-belts, bla-

des, tools, and other implements) and to adjustment/calibration 

works.

 

13.  EXTENDED WARRANTY

All SŰMA consumer products are covered with 24 or 12 months total 

warranty from the date of purchase for private/industrial users and 

rentals. This warranty extension does not substitute nor void the legal 

warranty. Customers should promptly notify eventual material, pro-

duction or workmanship claims on their detection. While asking for 

warranty service, customers should show copy of their purchase in-

voice or receipt. Buyer’s address and type/model of equipment must 

be clearly stated in the case of industrial users/contractors/dealers. 

All claims related to material or production failures during the total 

warranty time, shall be repaired notwithstanding eventual user’s faul-

ty/wrong operation or maintenance.  

Summary of Contents for FSW 5.5 H Evolution

































Reviews: