18
Retighten the screw (129) as shown
in diagram Fig. 6B, using the
screwdriver ended spanner. Check that
the tension controller operates correctly
by turning it left and right.
Take the tip of the tension cable (127),
sticking out of the bottom of the main
post (21) and connect it to the tension
support (134), as shown in Fig.6B.
Plug connector (126), coming out of the
main post (21), into connector (133),
coming out of the boss on the main
body (101), Fig.6B.
G2351
. Plug connector (19), coming out
of the main post (21), into connector
(102), coming out of the boss on the
main body (101), Fig.6A.
Slip the main post (21) over the boss
(101) on the main body in the direction
of the arrow, Fig.6, making sure not to
snag any of the cables.
Fit the screws (136), along with the
washers (137) and (107), removed
previously, Fig.6, and tighten securely.
Lower the bottom trim section (22) for
the main post (21) down over the boss
section of the main body (101), Fig.6.
Fit the bottom cover (54).
G2350
ATTENTION
:
When the
machine has been assembled, make
sure that the tension control (127)
works correctly.
5. FITTING THE FOCUS
BARS.-
Insert the focus bar spindle (108)
through the spacer bushes on the
main post (21), Fig.7, leaving it
centred.
Fit the spacer washers (17) as shown
in Fig.7. Insert the left focus bar (15L)
(marked with the letter “L”) onto the
focus bar spindle (108), Fig.7, then fit
the right focus bar (15R) (marked with
the letter “R”) on the other end of the
spindle. Fit the bolts (14) and the flat
washers (12-13) and with the help of
the box spanners tighten securely.
6. FITTING THE FEET.-
Take the right pedal (45), Fig.8,
(marked with the setter “R”) and slide
it onto the crank shaft (73) on the
right- hand side of the machine.
Now take washer (13) (52) and bolt
(14) and tighten securely.
Take the left pedal (45), Fig.8,
(marked with the setter “L”) and slide it
onto the shaft (73) on the left-hand
side of the machine.
Now take washer (13) (52) and bolt
(14) and tighten securely.
Attach the bottom covers (51), Fig.8,
and fit screws (85).
7. FITTING THE FOOT BARS.-
Take the right foot bar (45) and
position it on the “U” at the bottom of
the right focus bar (15R), Fig.9.
Insert screw (46), as shown in Fig.9A,
then fit the flat washer (44) and the
self locking nut (43), and tighten
securely.
Take the left foot bar (15L) and go
through the same assembly procedure
as with the right.
8. FITTING THE FOCUS BAR
SIDE COVERS TO THE FOOT
BARS.-
Next fit the footrest covers (42R) and
(42L) with the bottom of the joints on
the right side, Fig.10. Use screws (41)
to screw them together. Then do the
same with the other covers on the left-
hand side.
Summary of Contents for G2351IN/02
