16
4. FITTING THE MAIN POST.-
Once the bottom post cover, is fitted,
remove the screws (20) and washers
(13) and (90) from the bottom of the
main post (91).
Bring the main post (91) up to boss on
the main body (61), Fig.6.
Plug connector (89), coming out of the
main post (91), into connector (87),
coming out of the boss on the main
body (61), Fig.6.
Slip the main post (91) over the boss
(61) on the main body in the direction
of the arrow, Fig.6, making sure not to
snag any of the cables.
Fit the screws (20), along with the
washers (13) and (90), removed
previously, Fig.6, and tighten securely.
Lower the bottom trim section (88) for
the main post (91) down over the boss
section of the main body (61), Fig.6.
5.- FITTING THE FOCUS
BARS.-
Insert the focus bar spindle (25)
through the spacer bushes on the
main post (91), Fig.7, leaving it
centred.
Fit the spacer washers (24) as shown
in Fig.7. Insert the left focus bar (9L)
(marked with the letter “L”) onto the
focus bar spindle (25), Fig.7, then fit
the right focus bar (9R) (marked with
the letter “R”) on the other end of the
spindle. Fit the washered bolts (12)
and the flat washers (13-14) and with
the help of the box spanners tighten
securely.
6.- MOUNTING THE FOOT
ARMS.-
Take the left foot arm (26L) (marked
with the letter L) and insert it in the left
upper arm (9L) ensuring that the
letters coincide (L), Fig.8 insert screws
(16) and cap nuts (17) and tighten.
Follow the same procedure for the
right foot arm (26R).
7.- FITTING THE FEET.-
Take the right pedal (34R), Fig.9,
(marked with the setter “R”) and slide
it onto the crank shaft (56R) on the
right- hand side of the machine.
Now take washers (13) and (43) and
bolt (12) and tighten securely.
Attach the bottom cover for the right
foot (48R), Fig.9, and fi t screw (47).
Take the left pedal (34L), Fig.9,
(marked with the setter “L”) and slide it
onto the shaft (56L) on the left-hand
side of the machine.
Now take washer (13) and (43) and
bolt (12) and tighten securely.
Attach the bottom cover for the left
foot (48L), Fig.9, and fit screw (47).
Take the right foot (34R) and insert
plastic bushings (30) Fig 9, insert the
iron bushing (31) inside the plastic
bushings.
Position it in the "U" of the lower right
arm (9R) Fig 9, insert screw (29) as
shown in Fig 9 and take flat washer
(32) and self-locking nut (33) and
tighten firmly.
Take the left foot (34L), insert the
plastic bushings (30) Fig 9, insert the
iron bushing (31) inside the plastic
bushings.
Position it in the "U" of the lower left
arm (9L) Fig 9, insert screw (29) as
shown in Fig 9 and take flat washer
(32) and self-locking nut (33) and
tighten firmly.
Summary of Contents for G2354
