16
3. FITTING THE BOTTOM POST
COVER.-
Take the main post (25) and insert the
bottom post cover (29) in the direction
of the arrow, Fig.5.
4. FITTING THE MAIN POST.-
Once the bottom post cover, is fitted,
bring the main post (25) up to boss on
the main body (99), Fig.6.
Plug connector (116), coming out of
the main post (25), into connector
(119), coming out of the boss on the
main body (99), Fig.6A.
Slip the main post (25) over the boss
(99) on the main body in the direction
of the arrow, Fig.6, making sure not to
snag any of the cables.
Fit the screws (22), along with the
washers (19) and (21), Fig.6, and
tighten securely.
Lower the bottom trim section (29) for
the main post (25) down over the boss
section of the main body (99), Fig.6B.
5.- FITTING THE FOCUS BARS.-
Insert the left focus bar (8L) (marked
with the letter “L”) onto the focus bar
spindle (25), Fig.7, then fit the right
focus bar (8R) (marked with the letter
“R”) on the other end of the spindle.
Fit the washered bolts (20) and the flat
washers (18-19) and with the help of
the box spanners tighten securely.
Connect the terminals (118) and (117),
Fig.7A.
6.- MOUNTING THE FOOT ARMS.-
Take the left foot arm (33L) (marked
with the letter L) and insert it in the left
upper arm (8L) ensuring that the letters
coincide (L), Fig.8 insert screws (22)
and the flat washers (19-21) and tighten.
Follow the same procedure for the
right foot arm (33R).
7.- FITTING THE FEET.-
Take the right pedal (42R), Fig.9,
(marked with the setter “R”) and slide
it onto the crank shaft (81R) on the
right- hand side of the machine.
Now take washers (32) and (39) and
bolt (20) and tighten securely.
Finally, fit the caps (38).
Take the left pedal (42L), Fig.9,
(marked with the setter “L”) and slide it
onto the shaft (70L) on the left-hand
side of the machine.
Now take washer (19) and (39) and
bolt (20) and tighten securely.
Finally, fit the caps (38).
Take the right foot (42R) and position
it in the "U" of the lower right arm (8R)
Fig.9, insert screw (34) as shown in
Fig 9 and take flat washer (32) and
self-locking nut (31) and tighten firmly.
Take the left foot (42L), and position it
in the "U" of the lower left arm (8L)
Fig.9, insert screw (34) as shown in
Fig.9 and take flat washer (32) and
self-locking nut (31) and tighten firmly.
8.- FITTING THE FOCUS BAR
SIDE COVERS.-
Take the covers (15R), marked on the
inside with the letter “R”, and position
them at the spindle end with the bars
on the right hand side, as shown in
Fig.10B. Now use screws and (27) to
attach them.
Carry out the same procedure at the
other end of the bar using the covers
(15L) marked on the inside with the
letter “L”.
Summary of Contents for G2382U
