17
Plug connector (117), coming out of the
main post (116), into connector (118),
coming out of the boss on the main
body (72), Fig.4B.
Slip the main post (116) over the boss
(72) on the main body in the direction
of the arrow, Fig.4, making sure not to
snag any of the cables.
Make sure that the tension control
(112) functions correctly by turning it
clockwise and anticlockwise.
Fit the screws (99), along with the
washers (17) and (92), removed
previously, Fig.4, and tighten securely.
ATTENTION:
It is advisable to
retighten these screws after one
month of using the machine.
4. FITTING THE FOCUS BARS.-
Insert the focus bar spindle (103)
through the spacer bushes on the
main post (116), Fig.5, leaving it
centred.
Fit the spacer washers (11) as shown
in Fig.5. Insert the left focus bar (19L)
(marked with the letter “L”) onto the
focus bar spindle (103), Fig.5, then fit
the right focus bar (19R) (marked with
the letter “R”) on the other end of the
spindle. Fit the washered bolts (16)
and the flat washers (18) and with the
help of the box spanners, tighten
securely.
5. FITTING THE FOOT BARS.-
Take the right pedal (43R), Fig.6,
(marked with the setter “R”) and slide
it onto the crank shaft (80) on the
right- hand side of the machine.
Now take washer (50-17) and bolt (16)
and tighten securely.
Attach the bottom cover for the right
foot (49), Fig.6.
Take the left pedal (43L), Fig.6,
(marked with the setter “L”) and slide it
onto the shaft (60) on the left-hand
side of the machine.
Now take washer (50-17) and bolt (16)
and tighten securely.
Attach the bottom cover for the left
foot (49), Fig.6.
Take the left foot bar (43L) and
position it on the “U” at the bottom of
the left focus bar (19L), Fig.7.
Take the right foot bar (43R) and go
through the same assembly procedure
as with the left.
6. FITTING THE FOCUS BAR SIDE
COVERS TO THE FOOT BARS.-
Take the covers (20L and 20R),
marked on the inside with the letter
“R”, and position them at the end of
the foot bars with the inside of the
focus bars on the right hand side, as
shown in Fig.7. Now use screws (7
and 107) to attach them.
Carry out the same procedure using
the covers (20L and 20R) marked on
the inside with the letter “L”.
7. FITTING THE FOOTRESTS.-
Position the left footrest (48L) (marked
with the letter “L”) on top of the unit’s
left foot (43L), Fig.8, (left and right
refers to the user’s position doing
exercise) refit the screws (47), the
washers (44-45) and the nuts (46)
removed
previously
and
tighten
securely.
Next, position the right footrest (48R)
(marked with the letter “R”) on top of
the right foot (43R), refit the screws
(47), the washers (44-45) and the nuts
(46) removed previously and tighten
securely.
Summary of Contents for G2530O
