22
Lower the handlebar post cover (32)
for the main post (5) down over the
boss section of the main body (34).
Insert the axis (122) into the main post
(5) and put it in the center, Fig.5.
4.- FITTING THE FOOT BARS.-
Insert the washer (36) into the left axis
of rotation. Then take the left foot bar
(113) (marked with the letter “L”) and
insert the end bush onto the drive
spindle (E) on the main body (34).
Insert the screw (25) and the washers
(7), (24) to fix the left pedal tube (113),
Fig. 6.
Take the right foot bar (51), (marked
with the letter “R”) and go through the
same assembly procedure as with the
left.
5.- FITTING THE FOCUS
BARS.-
Insert the washer (18) in both sides of
the focus bar spindle.
Insert the left focus bar (117) (marked
with the letter “L”) onto the focus bar
spindle, insert the screws (25), the
washers (7), (24) and tighten securely,
Fig.7.
Take the right focus bar (22), (marked
with the letter “R”) and go through the
same assembly procedure as with the
left, Fig.7.
6.- FOOTREST ASSEMBLY.-
Insert the washer (18) in the right pedal
axis and insert the right footrest (65).
Place the pedal connector (74) on the
axis and fix it with the screws (13) and
washers (6), Fig.8.
Insert the screw (54) in the joint
between the right focus bar (22) and
the pedal tube and place the washer
(6) and the nut (20). Place the cover
(61) and fix it with the screws (62) and
(14), Fig. 9.
Perform the same assembly with the
left footrest (114), Fig.10.
ATTENTION: It is advisable to
retighten these screws after one
month of using the machine.
7.- FITTING THE UPPER
FOCUS BARS.-
Once you have assembled the lower
focus bars, take the left upper focus bar
(121) (marked with the letter “L”) and
insert it onto the boss for the low bar
(117), Fig.11, lining up the holes for the
screws.
Insert the screws (31) and the washers
(20).
Go through the same procedure for the
right upper focus bar (28) (marked with
the letter “R”).
8.- FITTING THE HANDLEBAR.-
Bring the handlebar (9) up to the main
post (5), insert the hand-grip cable in
through the slot as shown in Fig.12,
and pull it out through the top of the
handlebar stem.
Refit the screws (13) and the washers
(6), Fig.12 and tighten securely, then fit
the bracket cover (15) using the screw
(14).
9.- FITTING THE MONITOR.-
Next, connect terminals sticking out of
the handlebar (5), and terminals,
sticking out of the monitor (2) (3),
Fig.13.
Place the monitor (1) on top of the plate
on the main post (5), as shown in
Fig.13, making sure not to pinch the
wires.
Use supplied screws (132) to hold the
monitor in place, Fig.13.
Summary of Contents for G858
