18
Fig.1 Parts list:
(1) Rail.
(2) Main body.
(3) Main post.
(4) Left upper focus bar.
(5) Right upper focus bar.
(6) Left lower focus bar.
(7) Right lower focus bar.
(8) Left foot bar.
(9) Right foot bar.
(16) Left upper cover.
(17) Right upper cover.
(19) Front bar cover.
(20) Rear bar cover.
(21) Air outlet cover.
(27) Left lower bar cover.
(28) Right lower bar cover.
(39) Monitor.
(85) Bushing D17xD8.5x47
Fig.2 Fasteneers List:
(26) Screw M10x70x20
(44) Washer D8.5xD20xT1.5
(45) Washer D8.2xD25xT2.0
(47) Washer D10xD22xT2.0
(49) Washer D10.5xR100xT2.0
(50) Washer D8.5xR25xT2.0
(51) Washer D8
(52) Washer D10
(57) Nut M8
(62) Screw ST4x16
(65) Screw M5x15
(68) Screw M8x20
(69) Screw M8x40x20
(70) Screw M8x60x20
(72) Screw D9.4x23.5-M6/M6x12
(95) Screw M10x90x20
Wrenches
2.- FITTING THE MAIN BODY.-
ATTENTION: The assistance of a
second person is required for this
stage of the assembly.
Assembly the main body (2) onto rail
base (1), positioning according to the
figure, Fig.3, insert screws (95) and
with washers (52) (49) and screws (26)
with washers (52) (47) and tighten
slightly.
Align the structure and securely
tighten.
3.- FITTING THE MAIN POST.-
Put the cable through the main post
(3).
Bring the main post (3) up to boss on
the main body (2), Fig.4.
Slip the main post (3) over the boss on
the main body (2), Fig.4, making sure
not to snag any of the cables.
Insert the washers (50) (51) with the
screw (68) and the washers (44) with
the nuts (57) and screws (70).
Lower the handlebar post cover (32)
for the main post (5) down over the
boss section of the main body (34).
Insert the axis (122) into the main post
(5) and put it in the center, Fig.5.
Fit the left upper cover (16), the right
upper cover (17) and the air outlet
cover (21) and isert the screws (62).
4.- FITTING THE FOCUS BARS.-
Take the left lower focus bar (6)
(marked with the letter L) and insert it
onto the focus bar spindle, Fig.5. Fit the
screws (68) and washers (51) (45) and
tighten securely.
Insert the left upper focus bar in the left
lower focus bar (6) and fit the screws
(69), washers (50) and nuts (57).
Put the bar covers (19) (20) on using
the screws (65), Fig.5.
Take the right focus bar (7), (marked
with the letter “R”) and go through the
same assembly procedure as with the
left.
Summary of Contents for G875
