background image

                                                                                             

 

 

GENERAL: 

Remove all the part of your cycle from the carton and place them to the floor    carefully. Assembling your cycle is simple. 
Follow these instructions carefully and it should take you around 15-20 minutes. 
ATTACH THE Main frame 

 

Remove the pre-assembled 4 Allen head bolts (77) ,2 curl washers(66) and 2 flat washers (65) from the rear main frame (1). 

 

Attach rear main frame (9) to the hole of main frame (1) and fasten with 2 flat washers (65),2 curl washers(66) and 4 Allen head bolts(77) 

 

.Attach rear stabilizer (10)with 2 adjustment end caps to the welded cross bar bracket of Rear main frame (9) and fasten with 2 flat 
washers(65) , 2 spring washer(69) and carriages bolts(78). 

 

Attach front stabilizer (11) with 2 transportation wheels to the welded cross bar bracket of main frame (1) and fasten with 2 flat 
washers(65) ,2 spring washer(69) and 2 carriage bolts(1) .   

 

Assemble each pedal (20R&20L) to the crank . Pedal ”R” assemble with crank right side , Pedal ”L” assemble with crank left side : See the 
mark "R" & "L"(right and left) on the pedals (20R&20L) and crank . 

NOTE: The right pedal "R" should be threaded on clockwise. The left pedal "L" should be threaded on counter-clockwise. 

 

Attach the pedal straps to the pedals (20R&20L). 

NOTE: Adjust the pedal straps    to meet your foot/shoes size by 4 adjustable holes

.

 

       

 

 

Put the slide tube with slide bracket(7) into the main frame (1) and rear main frame(9), fasten with 4 flat washers(65) and 4 carriage 
bolt(76). 

 

Remove the pre-assembled 2 Allen head bolts (76) from slide bracket(7). Put the adjustable bar(15) to the side of the slide bracket(7) 
and fasten with head bolt(76) 

 

Put the upper rear cover (33,34) into the rear main frame(9) and slide tube(11), fasten with 5 screw (88) 

 

Put the lower rear cover(31,32) into the rear main frame(9) and fasten with 5 screw(88). 

 

Put the rear cover(29,30) into the main frame(1) and slide tube(11), fasten with 6 screw(88)

   

         

 

ASSEMBLY INSTRUCTYION 

Summary of Contents for H610U

















Reviews: