SK
LINE
sportkoncept
13
ENGLISH
GENERAL INSTRUCTIONS.-
This exercise machine is equipped with a dynamo that makes use of the energy produced by the user (while
exercising) to power the electronic monitor and the brake controller.
This monitor screen is touch sensitive, so to press a key just place your finger on the said key displayed on
the screen.
This exercise machine also includes a set of batteries that store enough energy to keep the electronic
monitor operating for 60 seconds after the exercise has finished.
Should the battery run down because of an operational fault, it can be recharged by using the adapter that is
supplied with the exercise machine.
To switch the monitor on, start doing exercise with the machine.
ATTENTION:
The adapter should be plugged into an appropriate socket. Make sure that the mains voltage
is compatible with the voltage for the adapter supplied with the machine.
The electronic monitor is designed to be easy and intuitive to use.The messages that appear on the bottom
screen (B) will guide the user throughout the whole exercise.
Nevertheless, we recommend that the gym instructor reads through this section carefully to become fully
familiar with the electronic monitor in order to show the user how to operate it correctly.
IMPORTANT: TO ENSURE THAT THE BATTERIES OPERATE CORRECTLY AND LAST LONGER IT IS
ADVISABLE TO RECHARGE THEM USING THE ADAPTER SUPPLIED WITH THE MACHINE.
PERSONALISING THE ELECTRONIC MONITOR.-
Follow the steps below to access the monitor’s personalisation mode: With the monitor switched off, press
and hold the RESET key and the O key at the same time, and then begin the exercise without releasing the
keys.
1) CHANGING FROM km to Mile.-
As soon as the monitor switches on, the words “FACTORY SETTINGS” will appear on the alphanumeric
screen (B), Fig.1. Press the ENTER key and the word UNITS will appear, press the ENTER key and the
word METRIC will flash, select the unit of speed by using the LEVEL
▲
and LEVEL
▼
keys (METRIC / Km. --
ENGLISH / Miles) press the ENTER key and the word “UNITS” will start flashing again, using the LEVEL
▲
key, pass on to the (2 WHEELSIZE) setting on the adjoining bottom screen.
If you wish to exit the personalisation mode, press the STOP key and the manual program will be displayed
on the LED array (A).
2) CHANGING DISTANCE PER REVOLUTION.-
With the word “WHEELSIZE” flashing, press the ENTER key and a figure between 0 to 80 will start flashing.
Select the value 80 using the LEVEL
▲
y LEVEL
▼
keys press the ENTER key and the word “WHEELSIZE”
will start flashing again, using the LEVEL
▲
key, pass on to the (3 LANGUAGE) setting on the adjoining
bottom screen. If you wish to exit the personalisation mode press the STOP key.
3) CHANGING LANGUAGE.-
With the word “LANGUAGE" flashing, press the ENTER key and the current language will start flashing.
Select your language using the LEVEL
▲
and LEVEL
▼
keys and then press ENTER, the word
“LANGUAGE” will start flashing again, using the LEVEL
▲
key , pass on to the (4 POWER) setting on the
adjoining bottom screen. If you wish to exit the personalisation mode press the STOP key.
4) SELF OR ELECTRICALLY POWERED.-
With the word “Power” flashing, press the ENTER key and the word ON or OFF will start flashing. Select the
option that is flashing by using the LEVEL
▲
and LEVEL
▼
keys.
The ON option is used to keep the monitor on at all times. If the ON option is selected
it will be necessary
to ensure that the machine is plugged into the mains supply by means of the adapter
. When you have
selected an option press the ENTER key to confirm and the word
"POWER" will start flashing again.
Stop
exercising.
Summary of Contents for SK LINE R250
Page 3: ...SK LINE LINE LINE LINE sportkoncept 3 Fig 2 Fig 3 Fig 4 Fig 5 ...
Page 4: ...SK LINE LINE LINE LINE sportkoncept 4 Fig 6 Fig 7 Fig 8 Fig 9 ...
Page 32: ...SK LINE LINE LINE LINE sportkoncept 32 R250 ...
Page 37: ...SK LINE sportkoncept Fig 1 ...
