BH FITNESS X4 ELLIPTICAL Owner'S Manual Download

Page: 4 / 36

BH FITNESS X4 Elliptical

BH Fitness • 20155 Ellipse • Foothill Ranch • CA • 92610

www.bhnorthamerica.com • Phone 949

-206-

8152 • Fax 949

-206-0013

SECTION 1

IMPORTANT SAFETY INSTRUCTIONS

Read all instructions before using the elliptical.

Notice: Before using this or any other exercise equipment

consult your family physician or

health care professional

to develop a well planned exercise program to fit your health needs.

If you encounter any pain or breathing discomfort while working out,

STOP!

and consult a

physician before continuing.

WARNING!

1. It is wise to always unplug this appliance from the electrical outlet immediately after use.

2. Keep children away from machine while in use.

3. Do not wear loose or dangling clothing while using the elliptical.

4. Maximum user weight of this elliptical is 325 lbs.

5. Keep a minimum clearance of 18” on each side and 24” at the rear of the elliptical for safety.

6. It is mandatory that you unplug the elliptical prior to cleaning to reduce the risk of electric

shock, serious burns, and the risk of injuries.

7. The elliptical should never be left unattended when in operation. Unplug the elliptical from

the outlet when not in use or when servicing the elliptical.

8. Close supervision is necessary when this appliance is used by or near children, invalids, or

disabled persons.

9. Use this appliance only for its intended use as described in this manual.

10. Do not use any attachment not recommended by the manufacturer.

11. Never operate this appliance if it has a damaged cord or plug, or if it is not working properly.

Call your service center for any service concerns before taking your elliptical in for repair.

12. Keep the cord away from heated surfaces.

13. Never drop or insert any object into any opening.

14. Do not use outdoors.

15. Do not operate where aerosol (spray) products are being used or where oxygen is being

administered.

16. To disconnect, turn all controls to the off position, then remove plug from outlet.

17. This appliance is intended for household use only.

SAVE THESE INSTRUCTIONS

Summary of Contents for X4 ELLIPTICAL





































Search results

Summary of Contents for X4 ELLIPTICAL

Reviews:

Related manuals for X4 ELLIPTICAL

Brands by name

Popular brands

BH FITNESS X4 ELLIPTICAL, Owner'S Manual

Search results

Summary of Contents for X4 ELLIPTICAL

Reviews:

Related manuals for X4 ELLIPTICAL

Brands by name

Popular brands