background image

Congratulations on your choice.

RIVA ADVANCE HE

are condensing high efficiency sealed chamber fan flue gas boilers.

They are fully electronically controlled and have electronic ignition.
The materials they are made of and the control systems they are equipped with give you safety,

a high level of comfort and energy savings to allow you to get the greatest benefit out of

independent heating.

RIVA ADVANCE HE

allow a higher efficiency by reducing the flue gas temperature such that

the water vapour formed during the combustion is condensed out.

This allows a gain of useful heat that otherwise would be lost.

Remember that...

n

The manual

---

must be read thoroughly, so that you will

be able to use the boiler in a safe and sen-

sible way;

---

must be carefully kept. It may be necess-

ary for reference in the future.

n

First lighting up

must be carried out by

competent and responsible engineer.

n

The manufacturer

---

disclaim all liability for any translations of

the present manual from which incorrect in-

terpretation may occur

---

cannot be held responsible for non---ob-

servance of instructions contained in this

manual or for the consequences of any pro-

cedure not specifically described.

Using the boiler...

n

Before lighting the boiler

you are ad-

vised to have a professionally qualified per-

son check that the installation of the gas

supply

---

is gas---tight;

---

is of the correct gauge for the flow to the

boiler;

---

is fitted with all the safety and control de-

vices required by the current Regulations.

n

Ensure that

---

the installer has connected the pressure

relief valve outlet to a drain pipe. The manu-

facturers are not responsible for damage

caused by opening of the pressure relief

valve and consequent escape of water, if not

connected correctly to the drain.

---

the installer has connected the conden-

sate outlet to a suitable drain pipe.

n

On detecting the smell of gas

---

don’t operate any electrical switches, the

telephone or any device that may produce

sparks;

---

open the windows and doors at once to

create a draught of air which will purge the

area;

---

shut off the gas cocks;

---

get the assistance of a qualified person.

n

Do not touch the appliance

with parts of

the body that are wet or damp and/or bare

feet.

n

Do not block or modify

the condensate

outlet and pipework

n

In case of structural work

or mainten-

ance near the exhaust duct and/or fume ex-

haust devices or their attachments, turn off

the appliance. On completion of the work,

have a professionally qualified person check

their efficiency.

n

Repairs

(under guarantee) must be car-

ried out only by an approved engineer, using

genuine spare parts. Thus do no more than

switching off the boiler yourself (see the in-

structions).

n

Your boiler

allows heating up of water to

a temperature less than boiling point;

--- must be connected to a central heating

system and/or a hot water supply system,

compatible with its performance and output;

Summary of Contents for RIVA ADVANCE HE M110.24SM













































Reviews: