background image

UPSI-2412DPx

Revision 1-1

29

F15  Recommendations for a long UPS service life

Over time, the capacity of the Supercaps decreases and the ESR (equivalent series resistance) increases. 
However, EOL is often defined as a reduction in capacity to 70 % and a doubling of the ESR. An important 
aspect for the aging of the Supercaps is the end-of-charge voltage and the operating temperature. 

LiFePO4 batteries also age over time depending on cycles, operating temperature and the level of the end-of-
charge voltage. The end-of-charge voltages are optimized so that they are at an optimium between service 
life and performance.

To extend the lifetime of the system, the device should not be placed near sources of heat and should be  
placed within good air-circulation. When using the UPSI-2412DP3 (LiFePO4 battery), a larger capacity than 
actually required should always be used. The less deep the packs are discharged, the longer the service life lasts.     

F16 Maintenance

The UPS contains no serviceable parts. In case of a malfunction the upstream power source has to be discon-
nected and cables have to be removed. Use a dry cloth for cleaning!

F17 Disposal

Electric and electronic devices must not be disposed with domestic waste! 
Please consider to each country’s own regulation about recycling and dispo-
sal of used batteries at the end of their lifetime or resending to any recycling 
organization.

F18 Disclaimer

We, the Bicker Elektronik GmbH, have checked the contents of this document for compliance with the hard-
ware and software described. Nevertheless, deviations can not be ruled out, so we assume no liability for the 
complete agreement. The information in this publication is checked regularly, necessary corrections are inclu-
ded in the updated versions. 

Suggestions for improvement as well as tips and criticism are always welcome.

Summary of Contents for UPSI-2412DP Series
































Reviews: