UPS-1000-B1
Revision 1
18
G12 Change output voltage (in UPS mode)
When the output voltage value is flashing, press any selection button
or
for 1 second, to change the out-
put voltage! The settings keep changing every 2 seconds, if you press the button.
10
4.10 Einstellungen
Es gibt zwei Möglichkeiten um die Einstellung an der USV zu ändern. Per Software in der Fabrik
bzw. Einstellungen über das LCD Display.
4.11.1 LCD Display
Drücken Sie die beiden Auswahltasten
△
und
▽
gleichzeitig für 3 Sekunden, bis die
LCD-Anzeige zu blinken beginnt. Durch das Menü gelangen Sie weiter, wenn abermals wieder
beide Tasten gleichzeitig gedrückt werden.
4.11.2 Ausgangsfrequenz der USV
nur für „
Kaltstart
“ (ohne Netz) ändern!
Wenn der Frequenzwert blinkt, drücken Sie eine beliebige Auswahltaste
△
bzw.
▽
für 1
Sekunde, um die Frequenzeinstellung zu ändern! Die Einstellung wird sich alle 2 Sekunden
ändern, wenn man die Taste betätigt.
Drücken Sie wieder die zwei Auswahltasten gleichzeitig zur nächsten Einstellung. Ohne weitere
Betätigung wird das LCD Display nach 30 Sekunden aufhören zu blinken und die Einstellung
beenden.
4.11.3 Ändern der Ausgangsspannung im USV Betrieb.
Wenn der Ausgangsspannung Wert blinkt, drücken Sie eine beliebige Auswahltaste
△
bzw.
▽
für 1 Sekunde, um die Ausgangsspannung zu ändern! Die Einstellung wird sich alle 2 Sekunden
ändern, wenn man die Taste betätigt.
Zum nächsten Menüpunkt gelangen Sie durch gleichzeitiges Drücken der beiden Auswahltasten
△
und
▽
.Ohne weitere Betätigung wird das LCD Display nach 30 Sekunden aufhören zu blinken
und die Einstellung beenden.
To get to the next menue item, press both selection buttons
and
at the same time. If you do not press it
again, the LCD display will stop flashing after 30 seconds and the setting will be completed.
G13 Auto recovery of UPS as soon as mains is present
If the automatical on/off function flashes, press any selection button
or
for 1 second, to change switch on/
off! The settings keep changing every 2 seconds, if you press the button.
off >> No auto recovery as soon as mains is present
On >> Auto recovery as soon as mains is present
On. S >> Auto recovery in “safety mode” as soon as mains is present
If the battery is still discharged from the previous UPS operation, the output of the UPS is only switched on after
the battery has been charged (at least 30 %).
To get to the next menue item, press both selection buttons
and
. If you do not press it again, the LCD
display will stop flashing after 30 seconds and the setting will be completed.
11
4.11.4 Automatische Einschaltung der USV sobald Netz anliegt
Wenn die automatische Ein bzw. Aus Funktion blinkt, drücken Sie eine beliebige Auswahltaste
△
bzw.
▽
für 1 Sekunde, um die Ein/Ausschaltung zu ändern! Die Einstellung wird sich alle 2
Sekunden ändern, wenn man die Taste betätigt.
off
Keine automatische Einschaltung sobald das Netz anliegt
On
Automatische Einschaltung sobald das Netz anliegt
On. S
Automatische Einschaltung im “Sicherheitsmodus” sobald das Netz anliegt
Falls die Batterie noch vom vorherigen USV Betrieb entladen sein sollte wird der Ausgang der USV
erst nach Ladung der Batterie (ca. 30%) zugeschgaltet.
Zum nächsten Menüpunkt gelangen Sie durch gleichzeitiges Drücken der beiden Auswahltasten
△
und
▽
.Ohne weitere Betätigung wird das LCD Display nach 30 Sekunden aufhören zu blinken
und die Einstellung beenden.
Summary of Contents for UPS-1000-B1
Page 3: ...UPS 1000 B1 Revision 1 3...