background image

4.   Miscellaneous 

 

ORM0043_2 

Modulating Controller Application Manual 

Page 8 

 

4.1   Supply Pressure Monitoring 

Supply pressure monitoring can be included on hydraulic 
positional systems to ensure that the hydraulic ring main 
pressure is above the required minimum pressure in 
order that the actuator can continue to be positioned. 

If 

Supply Px Check

 

is active then the hydraulic supply 

pressure transmitter should be linked to 

Supply Pressure

 

in order for the supply pressure to be monitored. 

If the 

Supply Pressure

 

drops below 

Min Supply Px SP

 

for 

greater than 

Supply Px Delay

 

then 

Low Supply Pressure

 

output is set active. If 

Fail On Low SPx

 

is also active then 

the actuator will position based on the fault override 
settings. 

If the 

Supply Pressure

 

signal is in fault for greater than 

Sig Fault Delay

 

then 

Supply Press Flt

 

is set active. If 

Fail 

On Low SPx

 

is also active then the actuator will position 

based on the fault override settings because it cannot be 
certain the pressure has not dropped below the 
minimum allowable supply pressure. 

4.2   Controller Access 

Whenever the controller is powered on the 

Controller 

On

 

output is set active. This is such that an output can be 

provided to confirm that the controller is powered on. 

Settings can be changed to affect when the controller 
can be in Manual Mode. 

If 

Auto Mode Switch 

is active then the controller will 

instantly revert to Automatic mode. Once in Automatic 
mode 

Auto Mode Switch 

will automatically reset to off 

so that Manual mode can be accessed again. 

 

To prevent access to Manual mode completely, 

Auto 

Mode Switch 

can be linked to a digital input which can 

hold 

Auto Mode Switch 

active and prevent access to 

Manual mode. 

If 

Man Mode Timer 

is active then the controller will 

revert to Automatic mode if the controller is not in 
Automatic mode for a specified time. The maximum 
allowable time can be set by changing 

Max Manual 

Time

.

 

NOTE: A minimum manual time is hard set to 2 minutes. 
If the 

Max Manual Time

 

is set to less than 2 minutes 

then the controller will revert to Automatic mode after 2 
minutes. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for Orange EHPC210















Reviews: