5.0
Operation
5.10
Erecting a
Part Load Tower
1. Performing a 'Part Load' is done automatically by the
Transtacker. To do a 'Part Load' successfully there are
some pointers you have to obied by:
i. The recommended minimum amount of layers a 'Part
Load' can be is;
a. 2 for 120x130cm bales
b. 3 for 120x90cm bales
c. 3 for 120x70cm bales
d. 3 for 80x90cm bales
e. 3 for 80x70cm bales
ii. Make sure the top layer of your 'Part Load' is not tied.
The top layer must lay along the bed
(
Fig. 39
)
.
iii.
If you have
the 'Turntable' left up,
make sure your
'Hooks' are retracted from your last stack layer.
iv.
T
he 'Side Gates' and 'Rear Clamps' must be open
when performing a Part Loa
d (
Fig. 39
).
Note
: If there is only 2 bales left. Make sure you place the
bales on top of each other (
Fig. 40
) creating 2 single layers.
Do NOT make a single layer as there will not be enough
weight to push the forks back to the rear.
CAUTION
: If you are traveling with a part load. Ensure that
the turntable is up with the hooks inserted into the last layer
of bales. Then perform 'Road Mode' to close all other
components of the Transtacker.
2.
In 'Stack Manual Mode' pull and hold the joystick back to
'Auto Tip Bed Up'
(
Fig. 38
)
.
This will engage the
Transtacker to recognize that it is only a part load. The
Transtacker will immediately start to tip up until it makes
connection with the 'Tip Bed Up Partial' sensor at a
recommended adjusted height of 20 degrees. Look at
Section 6.8.4
on how to alter the proximity sensors.
Fig. 38
WARNING
: When performing a 'Part Load', if the
sensor is not in contactable range, the 'Platform' will
lift all the way up. It is critical that you do NOT lift the
Transtacker's 'Platform' ove
r 40 Degrees (
Fig. 4
2
).
This could cause large damage to the 'Fork System'.
Fig. 41
Fig. 42
3. When the connection is made with the 'Tip Bed Up Partial',
the 'Fork System' will start to release the bales to the rear of
the Transtacker ready for further tipping.
4. Still holding the joystick on 'Auto Bed Tip Up', when the
bales reach the 'Bale Detect - Bed Full' sensor. The
Transtacker will automatically close the rear clamps and side
gates, securing the 'Part Load' Stack. The forks will fold down
and come to the front of the platform, contacting their
appropriate sensor. The 'Platform' will continue to tip up freely
now. Carry on the procedure from
Section 5.8 point 3.
Fig. 39
Fig. 40
14
Summary of Contents for Transtacker 4100
