8
.0
Trouble
s
hooting
8
.
8
Auto Open Troubleshooting
Function
Symptom
Cause
Fix
Guide Bar Extend /
Lowering Pickup Height
(Works in line with the
below function)
Guide Bar not opening at all
Machine PTO off
Turn PTO on (540)
Transtacker might think
there are layers on its count
Take off layers on the
Transtacker (
Section
9.4
).
Or manually open all
Transtacker functions
(
Section 5.12
)
Machine is not in Auto
Mode
Change mode of machine to
auto-mode and try again
Obstruction
Grab Arm may be
obstructed by the Pickup or
Pickup Shoe. This will false
trigger the pressure
transducer and cause the
Pickup to be lowered. Make
sure Guide Bar is free
‘Auto Open’ function wasn’t
active correctly
Try again with the joystick.
Make sure the joystick is
moved in its full travel
Guide Bar not opening all
the way
Guide Bar Pressure Sensor
has hit its desired pressure
Wear pads too tight,
restricting its outwards
movement. Loosen wear
pads and try again (
Section
6.12
)
Pickup lowering before
Guide Bar is fully extended
Pressure Relief valve in
Sequence valve is set too
low
Sequence valve needs
adjusting to increase
pressure
Pickup not lowering all the
way
Pressure Relief valve in
Sequence valve is set too
high
Sequence valve needs
adjusting to decrease
pressure
Pickup stuck in chassis
Retract guide bar and
extend again to release it.
Lubricate may be required
Pick is slow to lower
Pressure Relief valve in
Sequence valve is set too
high
Sequence valve needs
adjusting to decrease
pressure
Rear Clamps Opening
(Works in line with
above function)
Rear Clamps not opening at
all
Machine PTO off
Turn PTO on
Transtacker might think
there are layers on its count
Take off layers on the
Transtacker. Or manually
open Transtacker
Machine is not in Auto
Mode
Change mode of machine to
auto-mode and try again
‘Auto Open’ function wasn’t
active correctly
Try again with the joystick.
Make sure the joystick is
moved in its full travel
Rear Clamps not opening all
the way
Rear Clamps Pressure
Sensor has hit its desired
pressure
Make sure the rear clamp
pins are free to move.
Remove Plates over pins to
confirm
Forks Raise
Not raising after the Guide
Bar and Rear Clamps
Either one of the Guide Bar
or Rear Clamp pressure
sensors may not have hit its
trigger pressure
Decrease pressure
transducer pressure to
achieve its trigger
Trapped under the platform
Adjust the Fork trolley stop
on the platform to align the
Fork trolley (
Section
6.14
)
Other obstruction
Make sure the Fork is free
to raise
Auto Open (Can operating in Manual Functions)
Fig. 1
4
7
40
Summary of Contents for Transtacker 4100
