Side Gates Open unevenly
Wiring to solenoid wrong
way around
If the side gate wiring loom
is on the opposite side to
what it should be, it will
create a problem with the
proximity sensors
Turntable Raise to Full
(Works in line with
above and below
function)
Turntable doesn’t raise at
all
Left and Right-hand side
gate proximity sensors have
not been triggered
Adjust appropriately. Or
faulty sensor
Wiring fault
Turntable doesn’t raise to
full
Turntable Lift Rotate Sensor
can’t be found
Faulty rotate sensor
Magnet too far away
from sensor to read.
(
Section
6.9
)
CAN Bus wiring fault
Turntable Retract
(Works in line with
above 2 function)
Turntable does not retract
at all
Left and Right-hand side
gate proximity sensors have
not been triggered
Adjust Appropriately. Or
faulty sensor
Wiring Fault
Turntable does not retract
all the way
Turntable – Retract
proximity sensor could have
been falsely triggered
Faulty Proximity sensor
Faulty wiring
Forks being obstructed
The fork system maybe
restricting the rearward
push of the Turntable.
Check path is clear
The 3 stage Forks forward
ram may not be releasing
pressure. Check hydraulic
system
Side Gates obstructing
The Side Gates may have
not opened as far as they
should have. Make sure
bales are clear of Side Gates
Tines. Adjust sensor
appropriately (
Section
6.8
)
Hooks Retract
(Works in
line with below
function)
Hooks don’t retract at all
Turntable – Retract
proximity sensor has not
been triggered
Adjust sensor appropriately
(
Section
6.8
)
Turntable rotates when
hooks retract
Rotate selector valve is
stuck open
Replace Valve
Faulty wiring
Hooks don’t retract all the
way
Hooks Retract pressure
sensor trigger pressure is
set too low
Increase trigger pressure for
Hooks Retract
Side Gate Close
(Works
in line with above
function)
Side Gates don’t close at all
Turntable – Retract sensor
has not been triggered
Adjust sensor appropriately
(
Section
6.8
)
Left and Right Side Gate
pressure transducer trigger
is set to low
Increase Side Gate Left and
Right trigger pressure
Side Gates does not fold in
all the way
Obstruction
Due to varying bale lengths,
a bale could be restricting
the Side Gates from folding
in
Turntable Rotate
(Works in line with
below function)
Turntable does not rotate at
all
Side Gate Left or right or
Hooks retract pressure
transducer has not achieved
its trigger pressure
Decrease the appropriate
pressure transducer
Turntable Rotate rotary
Sensor calibration
Re-calibrate Rotate Rotary
sensor (
Section
6.9
)
Turntable rotate doesn’t
rotate all the way
Turntable Rotate Rotary
Sensor calibration
Re-calibrate Rotate Rotary
sensor (
Section
6.9
)
Hooks Insert when rotating
Hook selector valve is stuck
open
Replace Valve
8
.0
Trouble
s
hooting
8
.
10
Auto Stack Troubleshooting Continued.
Fig. 1
4
9
45
Summary of Contents for Transtacker 4100
