background image

06

Adjusting pedal resistance

You can adjust the pedal resistance on your Cyberbike™ using the knob loca-

ted at the base of the handlebar tube.

•  Rotate the knob in an anti-clockwise direction (towards the “-”) to decrease 

resistance when pedalling (See Fig 10).

•  Rotate the knob in a clockwise direction (towards the “+” ) to increase resis-

tance when pedalling (See Fig 10).

• Pedal resistance can also 

   be adjusted when pedalling.

4.ADVANCED FUNCTIONS 

4.a. Programming: 

4.a.I. How to programme the buttons:

 

• Press the “PROGRAM” button. The LED underneath this button will come on. 

•  Press the button or the direction that you wish to assign to another button 

(e.g. the A button). The LED will start to flash steadily.

•  Press the button that you now wish to use (e.g. the B button). The LED will flash 

rapidly for 2 seconds before going off. 

•  Pressing the B button will now carry out the action previously assigned to the 

A button. 

You can then reprogram any other button or direction as you wish. 

  

4.a.II. Cancelling programming:

• Press the “PROGRAM” button once. The LED will come on.

•  Press the programmed button (e.g. the B button). The LED will start to flash 

steadily.

•  Press the programmed button again (or the «PROGRAM” button). The LED will 

flash rapidly for 2 seconds before going off.

• The B button has now reverted to its original function. 

4.a.III. Cancelling all programming:

 

•  Press the “START/PAUSE” and “PROGRAM» buttons at the same time and hold 

down for 3 seconds. The LED located below the «PROGRAM” button will flash 

for 3 seconds. 

4.b. Calibrating the handlebar

•  Press the «PROGRAM” the “Y” button for 3 seconds. The LED located 

below the “PROGRAM” button will flash.

• Centre the handlebar. 

•  Press the “Y” button. The LED located below the “PROGRAM” button will now 

flash more rapidly. The central position of the handlebar has now been set. 

• Turn the handlebar to the left or right as far as it will go.

•  Press the «Y” button. The LED located below the “PROGRAM” button will flash 

for 3 seconds before going off. The handlebar calibration process is now 

complete. 

Restoring the manufacturer’s calibration (default setting): 

•  Press the “START/PAUSE” + “PROGRAM” buttons and hold down for 3 seconds. 

The LED will flash for 3 seconds. The handlebar calibration will revert to its 

default setting and any previous programming will be deleted.

4.c. Gamecube™ / Cyberbike™ modes

Use the Gamecube™ mode when you want to play with a Gamecube™/ Wii™ 

game. When you want to play with your Cyberbike™ game use the Cyber-

bike™ mode

 (See Fig 11)

.

CONFIGURATION: 

The A / B / X / Y / L / R / Z buttons, the directional pad and analog joysticks 

carry out the same actions as those on a traditional Gamecube™ controller.

Brake lever: the brake lever sends back the signal from the «B» button, and can 

also be reprogrammed. 

4.c.I. Gamecube™ mode

In Gamecube™ mode, FORWARD pedalling is the same as pressing the A but-

ton. 

In Gamecube™ mode, REVERSE pedalling is the same as pressing the B button. 

EN

G

LIS

H

CYBERBIKE

GAMECUBE

TM

TM

ES

PA

Ñ

O

L

FR

A

N

C

A

IS

Fig 10

Fig 11

Summary of Contents for CYBERBIKE

































Reviews: