background image

11.3 Music Sharing 
You can share the music or the mobile phone navigation APP instruction audio with intercom friend. 
11.3.1 Connect to your friend for 1-to-1 intercom. 
11.3.2 During intercom, press M button for 2 seconds and release.   
11.3.3 The intercom will end and the music you are listening to will be shared with your friend. 
11.3.4 To end music sharing, press V- button quickly for 3 times. 
11.4 GPS Navigation 

By pairing BK-T1 with a GPS Navigation device, you can hear navigation while riding. GPS Navigation 
Setting is available in BK-T1 Tool Program. 

12.Headset Pairing for Intercom / 

12.1 With BK-T1 #1 (1st BK-T1) powered on and press A button until the LED flashes blue rapidly. Or Press   

BK-T1 #1 A button and tap G-Sensor one time to make LED flash blue rapidly. 

12.2 Press BK-T1 #2 M button until the LED flashes red/blue rapidly. Or Press BK-T1 #2 M button and tap   

G-Sensor one time to make LED flash red/blue rapidly. 

12.3 The two headsets begin to pair with each other and after the completion, a voice notification <Headset A 

pairing completed.> and the LED flashes blue slowly. 

 

 

13. Headset Intercom Operation (1 on 1) / 

13.1 Make sure your BK-T1 had completed “Headset Pairing for Intercom”Each BK-T1 can memorize 3 other 

paired headsets and these 3 headsets will have different service priorities. The latest paired one will have 
the 1st service priority. For example, with 3 other headsets (A1, A2 and A3) already paired with a BK-T1, if 
A1 is the latest paired one, so it has the 1st service priority. If A3 is the first paired one, then it has the 3rd 
service priority. 

13.2 Activate/ End Intercom   
        Press A button for 2 seconds to activate intercom. 
        Press A button for 2 seconds to end intercom. 
13.3 In case of 3 other headsets are paired with BK-T1: 

 

 

14.Group Intercom / 

For BK-T1, Group Intercom is easy by chaining the 1 on 1 intercom. Refer to the figure illustrated below. 
14.1 With headset A paired with B, B paired with A and C, and C paired with B and D, then A, B, C and D can 

intercom all together.   

14.2 Press A button of headset A to intercom with headset B. 
14.3 Press A button of headset B to intercom with headset C. Now headset A can intercom with headset B and 

headset C. 

Summary of Contents for BK-T1









Reviews: