background image

Quick Start Guide 

 

     

 

Connecting to the Router 

 
1. 

Open the web browser and type 

http://192.168.1.254

 in the browser's address box. This 

number is the default IP address for this router. Press 

Enter.

 

2. 

A username and password window will appear. 

The default username is “admin”, and 

password is “admin”

. Press 

OK

 to proceed. 

3. 

You will get a status report web page and main menu screen. 

 

Please see the relevant sections of user manual for detailed instructions on how to 
configure your router. 

 

Troubleshooting 

 

1.  None of the LEDs are on when you turn on the router. 

Check the connection between the adapter and the router. If the error persists, you may 
have a hardware problem. In this case you should contact technical support. 

2.  Can’t ping any PCs on the LAN. 

Check the Ethernet LEDs on the front panel. The LED should be on for a port that has a PC 
connected. If it is off, check the cables between your router and the PC. Make sure you have 
uninstalled any software firewall for troubleshooting. Verify that the IP address and the 
subnet mask are consistent between the router and the workstations. 

3.  Frequent loss of ADSL linesync (disconnections). 

Ensure that all other devices connected to the same telephone line as your router (e.g. 
telephones, fax machines, analogue modems) have a line filter connected between them 
and the wall socket (unless you are using a Central Splitter or Central Filter installed by a 
qualified and licensed electrician), and ensure that all line filters are correctly installed and 
the right way around. Missing line filters or line filters installed the wrong way around can 
cause problems with your ADSL connection, including causing frequent disconnections. If 
you have a back-to-base alarm system you should contact your security provider for a 
technician to make any necessary changes. 

 

Product Support and Contact Information   

Most problems can be solved by referring to the 

Troubleshooting

 

section in the User Manual

.

 

If you cannot resolve the problem with the 

Troubleshooting

 

chapter, please contact the dealer 

where you purchased this product. 

 
 
 
 
 
 
 
 
 

Contact Billion

 

 
WORLDWIDE 

http://www.billion.com 

 

 
 
 
 
 
 
 

 

BiPAC 5400N 

R2

: V1.00EN

 

Summary of Contents for BiPAC 5400N R2








Reviews: