Billion BiPAC 6900AX(L)-2400 User Manual Download | Manualshive

Page: 193 / 276

background image

188

IPSec Lifetime:

Specify the number of minutes that IPSec will stay active before new encryption

and authentication key will be exchanged. Enter a value to negotiate and establish secure
authentication. Default is 60 minutes (3600 seconds). A short time increases security by forcing the
two parties to update the keys. However, every time when the VPN tunnel re- negotiates, access
through the tunnel will be temporarily disconnected.

Ping for Keep Alive:

Select the operation methods:



None:

The default setting is “None”. To this mode, it will not detect the remote IPSec peer

has been lost or not. It only follows the policy of Disconnection time after no traffic, which the
remote IPSec will be disconnected after the time you set in this function.



DPD:

Dead peer detection (DPD) is a keeping alive mechanism that enables the router to be

detected lively when the connection between the router and a remote IPSec peer has lost.
Please be noted, it must be enabled on the both sites.

Detection Interval:

The period cycle for dead peer detection. The interval can be 180~86400

seconds.

Idle Timeout:

Auto-disconnect the IPSec connection after trying several consecutive times.



Ping:

This mode will detect whether the remote IPSec peer has lost or not by pinging specify IP

address.

Ping IP:

Type the IP for ping operation.

It is able to IP Ping the remote PC with the specified IP

address and alert when the connection fails. Once alter message is received, Router will drop this
tunnel connection. Reestablish of this connection is required. Default setting is 0.0.0.0 which
disables the function.

Interval:

This sets the time interval between Pings to the IP function to monitor the connection

status. Default interval setting is 10 seconds. Time interval can be set from 0 to 3600 second, 0
second disables the function.

MTU:

Maximum Transmission Unit, maximum value is 1500.

«
...
191
192
193
194
195
...
»

Summary of Contents for BiPAC 6900AX(L)-2400





















































































































































































































































































Reviews:

No comments

Related manuals for BiPAC 6900AX(L)-2400

Brand: D-Link Pages: 4

Brand: D-Link Pages: 2

Brand: Tenda Pages: 57

Brand: Microsemi Pages: 2

Brand: Moxa Technologies Pages: 20

Brand: Vava Pages: 3

MiMo 300 Express

Brand: Hama Pages: 66

Brand: Telrad Pages: 10

Brand: Foxconn Pages: 28

NetVanta 150 Series

Brand: ADTRAN Pages: 28

3CRWEASYG73 - 11g Wireless LAN Outdoor

Brand: 3Com Pages: 4

DECT 1615 Series

Brand: Uniden Pages: 28

Brand: EliteConnect Pages: 214

Brand: Zks Pages: 20

SOUNDFLOW i17 +

Brand: WEEPLUG Pages: 22

WAP54GP - Wireless-G Access Point

Brand: Linksys Pages: 67

WAP54G - Wireless-G Access Point

Brand: Linksys Pages: 84

TEW-434APB - 54Mbps Wireless G PoE Access Point

Brand: TRENDnet Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands