Billion BiPAC 6900AX(L)-2400 User Manual Download

Page: 55 / 276

Route

Destination:

The IP address of destination network.

Gateway:

The IP address of the gateway this route uses.

Subnet Mask:

The destination subnet mask.

Flag:

Show the status of the route.



Show the route is activated or enabled.



H (host):

destination is host not the subnet.



Show that the outside gateway is needed to forward packets in this route.



Show that the route is reinstated from dynamic routing.



Show that the route is dynamically installed by daemon or redirecting.



Show the route is modified from routing daemon or redirect.

Metric:

Display the number of hops counted as the Metric of the route.

Service:

Display the service that this route uses.

Interface:

Display the existing interface this route uses.

Summary of Contents for BiPAC 6900AX(L)-2400





















































































































































































































































































Search results

Summary of Contents for BiPAC 6900AX(L)-2400

Reviews:

Related manuals for BiPAC 6900AX(L)-2400

Brands by name

Popular brands

Billion BiPAC 6900AX(L)-2400, User Manual

Search results

Summary of Contents for BiPAC 6900AX(L)-2400

Reviews:

Related manuals for BiPAC 6900AX(L)-2400

Brands by name

Popular brands