Billion BiPAC 6900AX(L)-2400 User Manual Download | Manualshive

Page: 73 / 276

background image

68

IGMP LAN to LAN Multicast:

Check to determine whether to support LAN to LAN (Intra LAN)

Multicast. If user want to have a multicast data source on LAN side and he wants to get IGMP
snooping enabled, then this LAN-to-LAN multicast feature should be enabled.

LAN side firewall:

Enable to drop all traffic from the specified LAN group interface. After activating it,

all incoming packets by default will be dropped, and the user on the specified LAN group interface
can't access CPE anymore. But, you can still access the internet service. If user wants to manage
the CPE, please turn to

IP Filtering Incoming

to add the allowing rules.

Note

that all incoming

packets by default will be dropped if the LAN side firewall is enabled and user cannot manage this
CPE from the specified LAN group.

DHCP Server

You can disable or enable the DHCP (Dynamic Host Configuration Protocol) server or enable the
router’s DHCP relay functions. The DHCP protocol allows your router to dynamically assign IP
addresses to PCs on your network if they are configured to obtain IP addresses automatically.



Disable

Disable the DHCP Server function.



Enable

Enable the DHCP function, enter the information wanted. Here as default.

Start IP Address:

The start IP address of the range the DHCP Server used to assign to the Clients.

End IP Address:

The end IP address f the range the DHCP Server used to assign to the Clients.

Leased Time (hour):

The leased time for each DHCP Client.

Option 66:

Click Enable to activate DHCP option 66 for some special devices, like IPTV Set Box.

The devices can get firmware or some special service from the TFTP server. User needs to set the
IP or hostname of the TFTP server.

User Router’s setting as DNS server:

Select whether to enable use router’s setting as DNS server

to allow different LAN group with different DNS server settings.

If enabled, the PCs on the LAN side obtain the router’s setting as DNS server. If disabled, please
specify exactly the primary/secondary DNS server.

Primary/Secondary DNS server:

Specify your primary/secondary DNS server for your LAN devices.



DHCP Server Relay

«
...
71
72
73
74
75
...
»

Summary of Contents for BiPAC 6900AX(L)-2400





















































































































































































































































































Reviews:

No comments

Related manuals for BiPAC 6900AX(L)-2400

Brand: Wavion Pages: 66

Brand: Zenitel Pages: 29

Brand: Conrad Pages: 8

Brand: Ubiquiti Pages: 12

8760 - Wireless Dual Radio 11a/b/g PoE Access...

Brand: 3Com Pages: 8

Brand: Cables to Go Pages: 63

Brand: Kasda Pages: 42

Verizon Jetpack AC791L

Brand: NETGEAR Pages: 2

Brand: Ryobi Pages: 84

Brand: Billion Pages: 61

Brand: Linksys Pages: 16

Brand: Linksys Pages: 40

Brand: Technicolor Pages: 80

Brand: Askey Pages: 17

Cable/DSL Wireless Broadband4-Port Router

Brand: Aztech Pages: 25

Brand: Billion Pages: 2

Brand: BandLuxe Pages: 80

Brand: Rosewill Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands