Billion BiPAC 6900AX(L)-2400 User Manual Download

Page: 88 / 276



WPA2

Protected Management Frame:

Select whether to enable protected management frame

mechanism. By default, it is disabled. If enabled, the network adapter of the attempting wireless
client should also support this feature.

WPA2 Preauthentication:

When a wireless client wants to handoff to another AP, with

preauthentication, it can perform 802.1X authentication to the new AP, and when handoff happens,
this mode will help reduce the association time.

Network Re-auth Interval:

the interval for network Re-authentication. This is in seconds.

WPA Group ReKey Internal:

The period of renewal time for changing the security key automatically

between wireless client and Access Point (AP). This is in seconds.

RADIUS Server IP Address:

RADIUS( Remote Authentication Dial In User Service), Enter the

IP address of RADIUS authentication server. This is in seconds.

RADIUS Server Port:

Enter the port number of RADIUS authentication server here.

RADIUS Key:

Enter the password of RADIUS authentication server.

WPA/WAPI Encryption:

There are two Algorithms, AES (Advanced Encryption Standard) and

TKIP(Temporal Key Integrity Protocol) which help to protect the wireless communication.



WPA2-PSK

Protected Management Frame:

Select whether to enable protected management frame

mechanism. By default, it is disabled. If enabled, the network adapter of the attempting wireless
client should also support this feature.

WPA/WAPI passphrase:

Enter the WPA.WAPI passphrase; you can

click here to display

to view it.

WPA Group ReKey Internal:

The period of renewal time for changing the security key automatically

between wireless client and Access Point (AP). This is in seconds.

WPA/WAPI Encryption:

There are two Algorithms, AES (Advanced Encryption Standard) and

TKIP(Temporal Key Integrity Protocol) which help to protect the wireless communication.

Summary of Contents for BiPAC 6900AX(L)-2400





















































































































































































































































































Search results

Summary of Contents for BiPAC 6900AX(L)-2400

Reviews:

Related manuals for BiPAC 6900AX(L)-2400

Brands by name

Popular brands

Billion BiPAC 6900AX(L)-2400, User Manual

Search results

Summary of Contents for BiPAC 6900AX(L)-2400

Reviews:

Related manuals for BiPAC 6900AX(L)-2400

Brands by name

Popular brands