51
SNR Margin (dB):
Show the Signal to Noise Ratio(SNR) margin.
Attenuation (dB):
This is estimate of average loop attenuation of signal.
Output Power (dBm):
Show the output power.
Attainable Rate (Kbps):
The sync rate you would obtain.
Rate (Kbps):
Show the downstream and upstream rate in Kbps.
MSGc (#of bytes in overhead channel message):
The number of bytes in overhead channel
message.
B (# of bytes in Mux Data Frame):
The number of bytes in Mux Data frame.
M (# of Mux Data Frames in FEC Data Frame):
The number of Mux Data frames in FEC frame.
T (Mux Data Frames over sync bytes):
The number of Mux Data frames over all the sync bytes.
R (# of check bytes in FEC Data Frame):
The number of check bytes in FEC frame.
S (ratio of FEC over PMD Data Frame length):
The ratio of FEC over PMD Data frame length
L (# of bits in PMD Data Frame):
The number of bit in PMD Data frame
D (interleaver depth):
Show the interleaver depth.
Delay (msec):
Show the delay time in msec.
INP (DMT symbol):
Show the DMT symbol.
Super Frames:
The total number of super frames.
Super Frame Errors:
the total number of super frame errors.
RS Words:
Total number of Reed-Solomon code errors.
RS Correctable Errors:
Total number of RS with correctable errors.
RS Uncorrectable Errors:
Total number of RS words with uncorrectable errors.
HEC Errors:
Total number of Header Error Checksum errors.
OCD Errors:
Total number of out-of-cell Delineation errors.
LCD Errors:
Total number of Loss of Cell Delineation.
Total Cells:
Total number of cells.
Data Cells:
Total number of data cells.
Bit Errors:
Total number of bit errors.
Total ES:
Total Number of Errored Seconds.
Total SES:
Total Number of Severely Errored Seconds.
Total UAS:
Total Number of Unavailable Seconds.
xDSL BER Test:
Click this button to start a bit Error Rate Test. The ADSL Bit Error Rate (BER) test
determines the quality of the ADSL connection. The test is done by transferring idle cells containing
a known pattern and comparing the received data with this known pattern to check for any errors.
Summary of Contents for BiPAC 8800AXL
