Part No. 500264
Form No. F082704A
Page 12 of 12
Purchased
from
Purchase
Date
Engine Service and Warranty
Contact your nearest engine manufacturer's authorized
servicing dealer.
22.1
21
Serial Plate
R
ecord your machine model, serial number and
date-of-purchase and where purchased
R
min
-1
BILLY GOAT INDUSTRIES INC.
1803 S.W. JEFFERSON STREET LEE'S SUMMIT, MO 64082 / USA
PHONE: 816-524-9666 FAX: 816-524-6983 www.billygoat.com
WARRANTY PROCEDURE
MAINTENANCE
continued
17
Solution
Problem
Possible Cause
Will not cut or has poor
cutting performance.
Unclog deck (see page 5). Sharpen blade.
Check engine RPM.(see page 11 for settings)
Dull Blade. Clogged deck. Excessive quantity of debris built up or
blocking blade. Engine RPM set too low.
Belt slips or smokes.
Operator's clutch lever not releasing clutch. Broken or out of
adjustment clutch cable. Worn or broken belt.
Belt tension too low . Belt worn or stretched. Pulleys worn or
damaged.
Abnormal vibration.
Loose or out of balance blade or loose engine.
Check blade and replace if required. Check Engine.
Increase tension at idler(see page 11). Replace belt. Replace
pulleys
Adjust clutch cable. Replace any worn, damaged or malfunctioning
parts.
TROUBLESHOOTING
Before Requesting Service Review These Suggestions
20
CLUTCH ADJUSTMENT
17.3
Clutch/Brake Adjustment:
As the clutch/brake wears, adjustments may be required to
maintain proper control cable tension, and clutch engagement.
If the clutch/brake begins slipping or squealing during normal
operation it may require an adjustment to increase the clutch
cable tension. A properly adjusted blade clutch should require a
minimum of 10 lbs. of force to completely depress the end of the
clutch lever.(See Fig. 4) Adjust by tightening or by loosening
clutch cable adjusting nut as required, located at the rear of the
engine base. When adjusting cable tension on blade control
cable be sure to leave slack in cable to allow for engagement of
blade brake. Replacement of cable or clutch/brake may be
necessary if adjustment will not allow for proper clutch and
brake engagement.
1803 S.W. Jefferson
Lee's Summit,
MO 64082 / USA
Tel (816) 524-9666
Fax (816) 524-6983
Model
Serial No.
Unit(Weight)
Engine Power
lbs.
kg
kW
rpm
WARNING:
If the clutch begins to squeal or slip, do not
continue to operate your unit until adequate adjustment or repair
has been performed.
Improper adjustment can cause clutch to slip and overheat,
greatly reducing machine performance and clutch life.
MOVE ADJUSTER OUT TO
INCREASE CABLE TENSION
MOVE ADJUSTER IN TO
DECREASE CABLE TENSION
MINIMUM FORCE = 10 LBS.
WHEN FULLY DEPRESSED
Fig. 4
Remove debris (see page 5 ). Contact an engine servicing dealer
for engine problems.(see page 10)
Adjust clutch cable. See page 10 Wheel Drive Clutch Adjustment.
Self propelled drive will not
release .
Clutch cable out of adjustment.
Engine is locked, will not
pull over.
Debris locked against blade. Engine problem.
No self propelling.
Clutch slips or squeals.
Clutch cable tension too low . Clutch worn or damaged.
Increase clutch cable tension (see above). Replace clutch/brake
Blade brake will not engage.
Inadequate slack in clutch cable . Clutch worn or damaged.
Adjust or replace cable (see above). Replace clutch/brake
The engine will not stop
The engine will not start
Damaged stop switch. Stop switch wire is disconnected. Stop switch
wire is worn or damaged.
Stop switch is off. Throttle is not in ON position. Out of gasoline. Bad
or old gasoline. Spark plug wire disconnected. Dirty air cleaner.
Replace stop switch. Connect stop switch wire. Replace stop switch
wire.
Check switch, throttle, & gasoline. Check for spark with an approved
tester. Clean or replace air cleaner. Contact service dealer.
Starter does not turn
(Electric start unit only)
Battery is too low or dead. Battery cable is disconnected or battery
terminal is corroded. Bad starter switch or wire harness. Bad starter.
Charge battery or replace with a new one. Clean battery terminals.
Replace starter switch. Replace Wire harness. Contact service dealer.
106 dB
Should a Billy Goat Machine fail due to a defect in material and / or
workmanship, the owner should make a warranty claim as follows:
-The Machine must be taken to the dealer from whom it was purchased or
to an authorized Servicing Billy Goat
Dealer
.
-The owner must present the remaining half of the Warranty Registration
Card, or, if this is not available, the invoice or receipt.
-The Warranty Claim will be completed by the authorized Billy Goat Dealer
and submitted to their respective Billy Goat Distributor for their territory.
Attention: Service Manager. Any parts replaced under warranty must be
tagged and retained for 90 days.
-The distributor service manager will sign off on the claim and submit it to
Billy Goat for consideration.
-The Technical Service Department at Billy Goat will study the claim and
may request parts to be returned for examination. Billy Goat will notify
their conclusions to the distributor service manager from whom the claim
was received.
-The decision by the Quality / Service department at Billy Goat to
approve or reject a Warranty claim is final and binding.
Note:
To process a Warranty Claim, it is necessary to quote the Model & Serial
Number which are printed on the Billy Goat Serial Plate (See owner’s manual).
