Part No. 890034 Form No. F101000A
Page 12 of 12
Engine Service and Warranty
Contact your nearest engine manufacturer's authorized
servicing dealer.
22.1
22
BILLY GOAT INDUSTRIES INC.
1803 S.W. Jefferson Street Lee's Summit, MO 64082 / USA
PHONE: 816-524-9666 FAX: 816-524-6983 WEBSITE: www.billygoat.com
WARRANTY PROCEDURE
Please fill in the WARRANTY CARD and send the upper part to Billy Goat.
The WARRANTY terms are stated on the lower part which remains with the
user. Whenever a Billy Goat Machine is faulty due to a defect in material
and / or workmanship, the owner should make a warranty claim as follows:
The Machine should be taken to the dealer from whom it was
purchased or to an authorized Billy Goat dealer.
The owner should present the remaining half of the Warranty
Registration Card, or, if this is not available, the invoice or receipt.
The Warranty Claim will be filled in by the authorized Billy Goat Dealer,
who will send it with the faulty part to Billy Goat headquarters.
The Quality / Service department at Billy Goat headquarters will study
the claim and parts and will notify their conclusions.
The decision by the Quality / Service department at Billy Goat
headquarters to approve or reject a Warranty claim is final and
binding.
Note: To process a Warranty Claim, it is necessary to quote the Model
& Serial number that are printed on the Billy Goat Serial Plate.
Purchased
from
Purchase
Date
21
Serial Plate
R
ecord your machine model, serial number and
date-of-purchase and where purchased
min
-1
Operator
1803 S. Jefferson
P.O. Box 308
Lee's Summit,
MO 64063 / USA
Tel (816) 524-9666
Fax (816) 524-6983
Model
Serial No.
Unit(Weight)
Engine Power
lbs.
kg
kW
rpm
Engine stalls or labors when
chipping.
Feeding branches into chipper too rapidly. Engine service may be
required.
Feed branches at a slower rate. Service engine.
Poor chipping performance.
Extremely hard wood. Dull or damaged chipper blade.
Avoid extremely hard wood. Sharpen or replace chipper blade (see
page 8).
Will not vacuum or has poor
vacuum performance.
Clean debris bag. Shake bag clean or wash. Adjust nozzle height.
Check for hose kit cap. Unclog nozzle or exhaust (see page 5).
Allow air to feed with debris.
Solution
Problem
Possible Cause
TROUBLESHOOTING
Before Requesting Service Review These Suggestions
Engine will not start.
Check stop switches, throttle, and gasoline. Connect spark plug wire.
Clean or replace air cleaner. Or contact a qualified service person.
Self propelled drive will not
release.
Clutch cable out of adjustment. Clutch not lubricated and is locked-
up.
Adjust clutch cable. See page 9 Clutch Adjustment. Oil clutch.
No self propelling.
Operator's bail not releasing clutch. Broken or out of adjustment
clutch cable. Worn or broken clutch assembly. Bracket control
assembly (item 112) out of adjustment.
Adjust clutch cable. Adjust bracket control assembly. Replace any
worn or damaged or malfunctioning parts.
Throttle in off position. Out of gasoline. Bad or old gasoline.
Spark Plug wire disconnected. Dirty air cleaner.
Abnormal vibration.
Loose or out of balance impeller or loose engine.
Check impeller and replace if required. Check Engine.
Engine is locked, will not
pull over.
Debris locked in chipper blade, hopper or inside impeller. Engine
problem.
See page 5, Clearing a clogged chipper hopper. Contact an engine
servicing dealer for engine problems.
Dirty debris bag. Nozzle height set too high or too low. Hose kit cap
missing. Clogged nozzle or exhaust. Excessive quantity of debris.
20
19
( Continued from
page 11 )
PARTS LIST
* Denotes
standard
hardware
item that
may be
purchased
locally.
95
L
A
L
A
p
109
Item
No.
Description
KD511SP
Part No.
Qty.
TKD511SP
Part No.
Qty.
86 Wheel With Sprocket A ss'y Cast ( 21, 94, 95, 96)
890242
2
890242
2
87 Chain 52 Pitch
890239
2
890239
2
88 Chain 40 Pitch
900323
1
900323
1
89 Washer Flat 5/16 (3/8 ID x 7/8 x 1 1/6)
*8171003
4
*8171003
4
90 Bolt Carriage 5/16 - 18 x 3/4
*8024039
4
*8024039
4
91 Washer Spring Lock 5/16
*8177011
4
*8177011
4
92 Nut Regular 5/16 - 18
*8142002
4
*8142002
4
93 Jackshaf t
900320
1
900320
1
94 Sprocket (per A ssemby) (size # 65A 26) 26 Teeth
890238
1
890238
1
95 Screw Self Tap 1/4-14 x 3/4 (Per A ssembly)
800505
5
800505
5
96 Washer Lock External Tooth (Per A ssembly)
*8181007
5
*8181007
5
97 Jackshaf t A ss'y (incl. 93, 101, 102, 107, 108, 109)
890197
1
890197
1
98 Shield Muf f ler TKDSP
890190
1
890190
1
99 Label Clutch
830503
1
830503
1
100 Label - Warning Guards
900327
1
900327
1
101 Bearing Plate
900317
2
900317
2
102 Bearing Ball (w ith Snap Ring)
900321
2
900321
2
103
104 Rod Bail Clutch
900970
1
900970
1
105
106
107 Sprocket - 17 Tooth
900303
1
900303
1
108 Sprocket - 8 Tooth
900302
2
900302
2
109 Roll Pin 3/16 Dia. x 1 1/4 Lg.
*8195166
4
*8195166
4
110 Locknut 5/16 - 18 Flange
850164
5
850164
5
111 Screw Cap 1/4-20 x 1-1/2 Hex
8041008
2
112 Bracket Control A ss'y (incl. 113, 114, 115)
900221
1
900221
1
113 Spring
900136
1
900136
1
114 Roll Pin 1/8" Dia. x 1 1/4 Lg.
*9195106
1
*9195106
1
115 Rod Clutch
900208
1
900208
1
116 Screw Cap 1/4-20 x 1" Lg.
*8041006
2
*8041006
2
117 Washer 1/4" Flat (5/16 ID x 3/4 Od x 1/16)
*8171002
4
*8171002
4
118 Guard Chain A ss'y TKDSP
890231
1
890195
1
119 Clip - Clutch Cable
900999
1
900999
1
120
121 Clutch Double Release
900307
1
900307
1
122
123 Label Read Ow ner's Manual
890301
1
890301
1
R
